Merge with /home/wd/git/u-boot/master

CHANGELOG

@@ -2,6 +2,193 @@
 Changes since U-Boot 1.1.4:
 ======================================================================
 
+* Prevent USB commands from working when USB is stopped.
+
+* Add rudimentary handling of alternate settings of USB interfaces.
+  This is in order to fix issues with some USB sticks timing out
+  during initialization. Some code readability improvements.
+
+* PPC440 DDR setup: Set SDRAM0_CFG0[PMU]=0 for best performance
+  AMCC suggested to set the PMU bit to 0 for best performace on
+  the PPC440 DDR controller.
+  Please see doc/README.440-DDR-performance for details.
+  Patch by Stefan Roese, 28 Jul 2006
+
+* AMCC bamboo (440EP) U-Boot image reduced to 384kbyte
+  Please see doc/README.bamboo for details.
+  Patch by Stefan Roese, 27 Jul 2006
+
+* Fix CONFIG_CMDLINE_EDITING implementation
+  Patch by Stefan Roese, 27 Jul 2006
+
+* Fix preboot message on TQM5200 after switching to hush parser.
+
+* MCC200: set default configuration to low_boot DDR,
+  and support for configurable options high_boot and/or SDRAM.
+
+* Add support for 256 MB SDRAM on CPU87
+  Patch by Josef Wagner, 25 Nov 2005
+
+* Add configuration for cam5200 board (based on TQM5200S).
+
+* More code cleanup
+
+* Disabled kvme080 board in MAKEALL because of build problems.
+
+* Code cleanup
+
+* Update NetStar board
+  Patch by Ladislav Michl, 03 Nov 2005
+
+* Make code better readable.
+  Patch by Ladislav Michl, 14 Sep 2005
+
+* Enable initrd ATAG for xm250 board.
+  Patch by Josef Wagner, 05 Sep 2005
+
+* Add readline cmdline-editing extension
+  Patch by JinHua Luo, 01 Sep 2005
+
+* Add support for friendly-arm SBC-2410X board
+  Patch by JinHua Luo, 01 Sep 2005
+
+* Fix multi-part image support on i386 platform.
+  Patch by David Updegraff, 19 Aug 2005
+
+* Add support for KVME080 board
+  Patch by Sangmoon Kim, 18 Aug 2005
+
+* Fix MIPS LE build problem
+  Patch by Matej Kupljen, 10 Aug 2005
+
+* Check argument count in "mii" command.
+  Problem pointed out by Andrew Dyer, 13 Jun 2005
+
+* Cleanup TQM5200 board configurations:
+  - make highboot configurations use environment at high end, too,
+    to avoid flash fragmentation
+  - always use redundand environment
+  - don't enable video code for modules without graphics controller
+  - provide useful (though different) mtdparts settings
+  - get rid of CONFIG_CS_AUTOCONF which was always set anyway
+
+* Extend mkconfig tool to print more useful target name
+
+* Add support for high-boot on TQM5200 and TQM5200S boards.
+  Hint: the CPLD on the TQM5200 must be programmed with a software
+  version supporting the high boot option! The new TQM5200S is
+  already supporting this option. On the TQM5200 this option will be
+  supported in configurations with MPC5200 rev B processors.
+  To actually "high boot", set jumper X30 on the STK52xx.
+  Patch by Martin Krause, 12 Jul 2006
+
+* Add support for new TQM5200 revisions
+  - Support for TQM5200S (short version without graphic controller)
+  - Support for modules with 'N' type S29GL128N Spansion flashes
+    (requires changes to flash layout)
+  - Support for MPC5200B cpu (mostly support for second SDRAM bank)
+  Patch by Martin Krause, 07 Jul 2006
+
+* Fix support for PS/2 keyboard on TQM85xx boards
+  The PS/2 keyobard driver for the TQM85xx modules only supports the
+  internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't
+  include a DUART, the TQM8560 modules can't be used with the PS/2
+  keyboard controller on the STK85xx board.
+  The PS/2 keyboard driver should work with the modules TQM8540,
+  TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet.
+  Make sure the PS/2 controller on the STK85xx is programmed. Jumper
+  settings: X66 1-2, 9-10; X61 2-3
+  Patch by Martin Krause, 21 Jun 2006
+
+* Adjust RTC century handling on STK52xx board to match Linux driver.
+  Patch by Martin Krause, 12 Jun 2006
+
+* Adjust filenames for USB update images on TRAB board.
+  During an automatic update via USB stick, U-Boot searches for
+  images with the name "firmware.img" and "kernel.img". This names
+  are now changed to "firmw_01.img" and "kernl_01.img". This is done,
+  to prevent updates of new boards (with the new macronics "c" step
+  flashes) with old, incompatible firmware or kernel versions.
+  Patch by Martin Krause, 21 Jun 2006
+
+* Bugfix in VFD routine on TRAB board.
+  Make sure upper lext pixel can be set to blue, too
+  (so far only red was possible).
+  Patch by Martin Krause, 15 Feb 2006
+
+* Enable buffered flash writes for TB5200 board.
+
+* Fix some bugs in TRAB board flash driver.
+  - increase CFG_FLASH_ERASE_TOUT from 2 to 15 seconds
+  - use CFG_FLASH_WRITE_TOUT for programming instead of CFG_FLASH_ERASE_TOUT
+  - remove "Unlock Bypass" mode, because macronix flashes do not support
+    this mode officially
+  - fix flash reset command from 0x00FF to 0x00F0. 0x00FF is only specified
+    for Intel compatible flashes, not for AMD compatible.
+  Patch by Martin Krause, 15 Feb 2006
+
+* Add additional error messages to flash driver on TRAB board
+  (for erase errors and timeout errors)
+  Patch by Martin Krause, 14 Feb 2006
+
+* Add support for TB5200 board
+  The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module
+  integrated in a little aluminium case.
+  Patch by Martin Krause, 8 Jun 2006
+
+* Enable buffered flash writes for TQM5200 board.
+
+* Fix problems with SanDisk Corporation Cruzer Micro USB memory stick.
+
+* Add support for TQM885D board.
+  Patch by Martin Krause, 20 Mar 2006
+
+* Fix FEC initialisation: All MII configuration is done via FEC1
+  registers, but MII_SPEED was configured according to FEC used. So
+  if only FEC2 was used, this caused the real MII_SPEED register in
+  FEC1 to stay uninitalised, leqading to "mii_send STUCK!" messages.
+  Fix: always configure MII_SPEED on FEC1 only.
+  Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* Add support for SPC1920 board.
+  Patch by Markus Klotzbuecher, 12 Jul 2006
+
+* MCC200 board: support console on any one of the Quad UART ports.
+
+* Fix error in flash protection calculation on MCC200 board.
+
+* Major PCMCIA Cleanup to make code better readable and maintainable.
+  Notes:
+  - Board-dependend code for RPXLITE and RPXCLASSIC-based boards
+    placed to the drivers/rpx_pmcia.c file to avoid duplication.
+    Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c).
+  - drivers/i82365.c has been split into two parts located at
+    board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are
+    the only boards using CONFIG_82365).
+  - Changes were tested for clean build and *very* *few* boards.
+
+* Fix timer problems on AMCC yucca board.
+  Set Timer Clock Select to use CPU clock as a timer input source.
+
+* Bring yucca config more in line with other AMCC boards.
+
+* Add AMCC bamboo board to MAKEALL build script.
+
+* Fix AMCC bamboo eval board compilation errors.
+
+* Add system memory to the PCI region list for AMCC PPC44x CPUs.
+  Enabled it for Yucca board.
+
+* Cleanup config file and bootup output for Yucca board.
+
+* Fix CONFIG_440_GX define usage.
+
+* Remove autogenerated bmp_logo.h file.
+
+* Add support for AMCC 440SPe CPU based eval board (Yucca).
+
+* Call serial_initialize() before first debug() is used.
+
 * Code cleanup
 
 * Various USB related patches

CREDITS

@@ -233,6 +233,7 @@ D: Port to Windriver ppmc8260 board
 N: Sangmoon Kim
 E: dogoil@etinsys.com
 D: Support for debris board
+D: Support for KVME080 board
 
 N: Frederick W. Klatt
 E: fred.klatt@windriver.com

MAINTAINERS

@@ -197,6 +197,7 @@ Brad Kemp <Brad.Kemp@seranoa.com>
 Sangmoon Kim <dogoil@etinsys.com>
 
 	debris			MPC8245
+	KVME080			MPC8245
 
 Thomas Lange <thomas@corelatus.se>
 

MAKEALL

@@ -27,14 +27,14 @@ LIST_5xx="	\
 LIST_5xxx="	\
 	BC3450		cpci5200	EVAL5200	icecube_5100	\
 	icecube_5200	lite5200b	mcc200		o2dnt		\
-	pf5200		PM520		Total5100	Total5200	\
+	pf5200		PM520		TB5200		Total5100	\
-	Total5200_Rev2	TQM5200						\
+	Total5200	Total5200_Rev2	TQM5200		TQM5200_B	\
+	TQM5200S							\
 "
 
 #########################################################################
 ## MPC8xx Systems
 #########################################################################
-
 LIST_8xx="	\
 	Adder87x	GENIETV		MBX860T		R360MPI		\
 	AdderII		GTH		MHPC		RBC823		\
@@ -44,16 +44,18 @@ LIST_8xx="	\
 	CCM		IP860		NETPHONE	RPXlite_DW	\
 	cogent_mpc8xx	IVML24		NETTA		RRvision	\
 	ELPT860		IVML24_128	NETTA2		SM850		\
-	EP88x		IVML24_256	NETTA_ISDN	SPD823TS	\
+	EP88x		IVML24_256	NETTA_ISDN	spc1920		\
-	ESTEEM192E	IVMS8		NETVIA		svm_sc8xx	\
+	ESTEEM192E	IVMS8		NETVIA		SPD823TS	\
-	ETX094		IVMS8_128	NETVIA_V2	SXNI855T	\
+	ETX094		IVMS8_128	NETVIA_V2	svm_sc8xx	\
-	FADS823		IVMS8_256	NX823		TOP860		\
+	FADS823		IVMS8_256	NX823		SXNI855T	\
-	FADS850SAR	KUP4K		pcu_e		TQM823L		\
+	FADS850SAR	KUP4K		pcu_e		TOP860		\
-	FADS860T	KUP4X		QS823		TQM823L_LCD	\
+	FADS860T	KUP4X		QS823		TQM823L		\
-	FLAGADM		LANTEC		QS850		TQM850L		\
+	FLAGADM		LANTEC		QS850		TQM823L_LCD	\
-	FPS850L		lwmon		QS860T		TQM855L		\
+	FPS850L		lwmon		QS860T		TQM850L		\
-	GEN860T		MBX		quantum		TQM860L		\
+	GEN860T		MBX		quantum		TQM855L		\
-	GEN860T_SC					uc100		\
+	GEN860T_SC					TQM860L		\
+							TQM885D		\
+							uc100		\
 							v37		\
 "
 
@@ -72,10 +74,10 @@ LIST_4xx="	\
 	luan		METROBOX	MIP405		MIP405T		\
 	ML2		ml300		ocotea		OCRTC		\
 	ORSG		p3p440		PCI405		pcs440ep	\
-	PIP405		PLU405		PMC405	        PPChameleonEVB	\
+	PIP405		PLU405		PMC405		PPChameleonEVB	\
-	sbc405		VOH405		VOM405          W7OLMC		\
+	sbc405		VOH405		VOM405		W7OLMC		\
 	W7OLMG		walnut		WUH405		XPEDITE1K	\
-	yellowstone	yosemite					\
+	yellowstone	yosemite	yucca		bamboo		\
 "
 
 #########################################################################
@@ -93,9 +95,9 @@ LIST_8220="	\
 LIST_824x="	\
 	A3000		barco		BMW		CPC45		\
 	CU824		debris		eXalion		HIDDEN_DRAGON	\
-	MOUSSE		MUSENKI		MVBLUE		OXC		\
+			MOUSSE		MUSENKI		MVBLUE		\
-	PN62		Sandpoint8240	Sandpoint8245	sbc8240		\
+	OXC		PN62		Sandpoint8240	Sandpoint8245	\
-	SL8245		utx8245						\
+	sbc8240		SL8245		utx8245				\
 "
 
 #########################################################################
@@ -179,9 +181,10 @@ LIST_ARM9="	\
 	ap966		cp920t		cp922_XA10	cp926ejs	\
 	cp946es		cp966		lpd7a400	mp2usb		\
 	mx1ads		mx1fs2		netstar		omap1510inn	\
-	omap1610h2	omap1610inn	omap730p2	scb9328		\
+	omap1610h2	omap1610inn	omap730p2	sbc2410x	\
-	smdk2400	smdk2410	trab		VCMA9		\
+	scb9328		smdk2400	smdk2410	trab		\
-	versatile	versatileab	versatilepb	voiceblue
+	VCMA9		versatile	versatileab	versatilepb	\
+	voiceblue							\
 "
 
 #########################################################################

Makefile

@@ -7,7 +7,7 @@
 #
 # This program is free software; you can redistribute it and/or
 # modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
+# published by the Free Software Foundatio; either version 2 of
 # the License, or (at your option) any later version.
 #
 # This program is distributed in the hope that it will be useful,
@@ -323,13 +323,25 @@ lite5200b_LOWBOOT_config:	unconfig
 	@./mkconfig -a IceCube  ppc mpc5xxx icecube
 
 mcc200_config	\
-mcc200_lowboot_config:	unconfig
+mcc200_SDRAM	\
+mcc200_highboot	\
+mcc200_highboot_SDRAM:	unconfig
 	@ >include/config.h
-	@[ -z "$(findstring lowboot_,$@)" ] || \
+	@[ -n "$(findstring highboot,$@)" ] || \
-		{ echo "TEXT_BASE = 0xFC000000" >board/mcc200/config.tmp ; \
+		{ echo "... with lowboot configuration" ; \
-		  echo "... with lowboot configuration" ; \
 		}
-	@./mkconfig mcc200 ppc mpc5xxx mcc200
+	@[ -z "$(findstring highboot,$@)" ] || \
+		{ echo "TEXT_BASE = 0xFFF00000" >board/mcc200/config.tmp ; \
+		  echo "... with highboot configuration" ; \
+		}
+	@[ -n "$(findstring _SDRAM,$@)" ] || \
+		{ echo "... with DDR" ; \
+		}
+	@[ -z "$(findstring _SDRAM,$@)" ] || \
+		{ echo "#define CONFIG_MCC200_SDRAM"	>>include/config.h ; \
+		  echo "... with SDRAM" ; \
+		}
+	@./mkconfig -a mcc200 ppc mpc5xxx mcc200
 
 o2dnt_config:
 	@./mkconfig o2dnt ppc mpc5xxx o2dnt
@@ -356,15 +368,21 @@ smmaco4_config: unconfig
 	@./mkconfig -a smmaco4 ppc mpc5xxx tqm5200
 
 spieval_config:	unconfig
-	@echo "#define CONFIG_CS_AUTOCONF">>include/config.h
-	@echo "... with automatic CS configuration"
 	@./mkconfig -a spieval ppc mpc5xxx tqm5200
 
+TB5200_B_config \
+TB5200_config:	unconfig
+	@[ -z "$(findstring _B,$@)" ] || \
+		{ echo "#define CONFIG_TQM5200_B"	>>include/config.h ; \
+		  echo "... with MPC5200B processor" ; \
+		}
+	@./mkconfig -n $@ -a TB5200 ppc mpc5xxx tqm5200
+
 MINI5200_config	\
 EVAL5200_config	\
 TOP5200_config:	unconfig
 	@ echo "#define CONFIG_$(@:_config=) 1"	>include/config.h
-	@./mkconfig -a TOP5200 ppc mpc5xxx top5200 emk
+	@./mkconfig -n $@ -a TOP5200 ppc mpc5xxx top5200 emk
 
 Total5100_config		\
 Total5200_config		\
@@ -395,20 +413,39 @@ Total5200_Rev2_lowboot_config:	unconfig
 	@./mkconfig -a Total5200 ppc mpc5xxx total5200
 
 TQM5200_config	\
+TQM5200_B_config \
+TQM5200_B_HIGHBOOT_config \
+TQM5200S_config \
+TQM5200S_HIGHBOOT_config \
 TQM5200_STK100_config \
+cam5200_config \
 MiniFAP_config:	unconfig
 	@ >include/config.h
 	@[ -z "$(findstring MiniFAP,$@)" ] || \
 		{ echo "#define CONFIG_MINIFAP"	>>include/config.h ; \
 		  echo "... TQM5200_AC on MiniFAP" ; \
 		}
+	@[ -z "$(findstring cam5200,$@)" ] || \
+		{ echo "#define CONFIG_CAM5200"	>>include/config.h ; \
+		  echo "#define CONFIG_TQM5200S"	>>include/config.h ; \
+		  echo "#define CONFIG_TQM5200_B"	>>include/config.h ; \
+		  echo "... TQM5200S on Cam5200" ; \
+		}
 	@[ -z "$(findstring STK100,$@)" ] || \
 		{ echo "#define CONFIG_STK52XX_REV100"	>>include/config.h ; \
 		  echo "... on a STK52XX.100 base board" ; \
 		}
-	@echo "#define CONFIG_CS_AUTOCONF">>include/config.h ;
+	@[ -z "$(findstring TQM5200_B,$@)" ] || \
-	@echo "... with automatic CS configuration" ;
+		{ echo "#define CONFIG_TQM5200_B"	>>include/config.h ; \
-	@./mkconfig -a TQM5200 ppc mpc5xxx tqm5200
+		}
+	@[ -z "$(findstring TQM5200S,$@)" ] || \
+		{ echo "#define CONFIG_TQM5200S"	>>include/config.h ; \
+		  echo "#define CONFIG_TQM5200_B"	>>include/config.h ; \
+		}
+	@[ -z "$(findstring HIGHBOOT,$@)" ] || \
+		{ echo "TEXT_BASE = 0xFFF00000" >board/tqm5200/config.tmp ; \
+		}
+	@./mkconfig -n $@ -a TQM5200 ppc mpc5xxx tqm5200
 
 #########################################################################
 ## MPC8xx Systems
@@ -708,6 +745,9 @@ RRvision_LCD_config:	unconfig
 SM850_config	:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx tqm8xx
 
+spc1920_config:
+	@./mkconfig $(@:_config=) ppc mpc8xx spc1920
+
 SPD823TS_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx spd8xx
 
@@ -745,6 +785,7 @@ TQM855M_config		\
 TQM860M_config		\
 TQM862M_config		\
 TQM866M_config		\
+TQM885D_config		\
 virtlab2_config:	unconfig
 	@ >include/config.h
 	@[ -z "$(findstring _LCD,$@)" ] || \
@@ -984,6 +1025,9 @@ yosemite_config:	unconfig
 yellowstone_config:	unconfig
 	@./mkconfig $(@:_config=) ppc ppc4xx yellowstone amcc
 
+yucca_config:	unconfig
+	@./mkconfig $(@:_config=) ppc ppc4xx yucca amcc
+
 #########################################################################
 ## MPC8220 Systems
 #########################################################################
@@ -1034,6 +1078,9 @@ eXalion_config: unconfig
 HIDDEN_DRAGON_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x hidden_dragon
 
+kvme080_config: unconfig
+	@./mkconfig $(@:_config=) ppc mpc824x kvme080 etin
+
 MOUSSE_config: unconfig
 	@./mkconfig $(@:_config=) ppc mpc824x mousse
 
@@ -1591,6 +1638,9 @@ omap730p2_cs3boot_config :	unconfig
 	fi;
 	@./mkconfig -a $(call xtract_omap730p2,$@) arm arm926ejs omap730p2 NULL omap
 
+sbc2410x_config: unconfig
+	@./mkconfig $(@:_config=) arm arm920t sbc2410x NULL s3c24x0
+
 scb9328_config	:	unconfig
 	@./mkconfig $(@:_config=) arm arm920t scb9328 NULL imx
 
@@ -1971,6 +2021,7 @@ clean:
 	rm -f board/netstar/*.srec board/netstar/*.bin
 	rm -f board/trab/trab_fkt board/voiceblue/eeprom
 	rm -f board/integratorap/u-boot.lds board/integratorcp/u-boot.lds
+	rm -f include/bmp_logo.h
 
 clobber:	clean
 	find . -type f \( -name .depend \

README

@@ -306,7 +306,7 @@ The following options need to be configured:
 
 		CONFIG_ARMADILLO,	CONFIG_AT91RM9200DK,	CONFIG_CERF250,
 		CONFIG_CSB637,		CONFIG_DELTA,		CONFIG_DNP1110,
-	 	CONFIG_EP7312,		CONFIG_H2_OMAP1610,	CONFIG_HHP_CRADLE,
+		CONFIG_EP7312,		CONFIG_H2_OMAP1610,	CONFIG_HHP_CRADLE,
 		CONFIG_IMPA7,	    CONFIG_INNOVATOROMAP1510,	CONFIG_INNOVATOROMAP1610,
 		CONFIG_KB9202,		CONFIG_LART,		CONFIG_LPD7A400,
 		CONFIG_LUBBOCK,		CONFIG_OSK_OMAP5912,	CONFIG_OMAP2420H4,
@@ -1552,6 +1552,12 @@ The following options need to be configured:
 		of the backslashes before semicolons and special
 		symbols.
 
+- Commandline Editing and History:
+		CONFIG_CMDLINE_EDITING
+
+		Enable editiong and History functions for interactive
+		commandline input operations
+
 - Default Environment:
 		CONFIG_EXTRA_ENV_SETTINGS
 

board/MAI/bios_emulator/scitech/src/pm/win32/event.c

@@ -147,14 +147,14 @@ void _EVT_pumpMessages(void)
 		if (EVT.oldMove != -1) {
 		    EVT.evtq[EVT.oldMove].where_x = evt.where_x;/* Modify existing one  */
 		    EVT.evtq[EVT.oldMove].where_y = evt.where_y;
-/*                  EVT.evtq[EVT.oldMove].relative_x += mickeyX;    // TODO! */
+/*                  EVT.evtq[EVT.oldMove].relative_x += mickeyX;    / / TODO! */
-/*                  EVT.evtq[EVT.oldMove].relative_y += mickeyY;    // TODO! */
+/*                  EVT.evtq[EVT.oldMove].relative_y += mickeyY;    / / TODO! */
 		    evt.what = 0;
 		    }
 		else {
 		    EVT.oldMove = EVT.freeHead; /* Save id of this move event   */
-/*                  evt.relative_x = mickeyX;    // TODO! */
+/*                  evt.relative_x = mickeyX;    / / TODO! */
-/*                  evt.relative_y = mickeyY;    // TODO! */
+/*                  evt.relative_y = mickeyY;    / / TODO! */
 		    }
 		}
 	    else

board/Marvell/include/core.h

@@ -91,7 +91,10 @@ extern unsigned int INTERNAL_REG_BASE_ADDR;
 #define _1G		0x40000000
 #define _2G		0x80000000
 
+#ifndef	BOOL_WAS_DEFINED
+#define BOOL_WAS_DEFINED
 typedef enum _bool{false,true} bool;
+#endif
 
 /* Little to Big endian conversion macros */
 

board/amcc/bamboo/bamboo.c

@@ -435,7 +435,7 @@ long int initdram (int board_type)
 	 */
 	init_spd_array();
 
-	dram_size = spd_sdram (0);
+	dram_size = spd_sdram();
 
 	return dram_size;
 }

board/amcc/bamboo/bamboo.h

@@ -283,10 +283,8 @@
 /*----------------------------------------------------------------------------+
   | PPC440EP GPIOs addresses.
   +----------------------------------------------------------------------------*/
-#define GPIO0_BASE	 0xEF600B00
 #define GPIO0_REAL	 0xEF600B00
 
-#define GPIO1_BASE	 0xEF600C00
 #define GPIO1_REAL	 0xEF600C00
 
 /* Offsets */
@@ -331,17 +329,6 @@
 #define GPIO_IS3(x)	(x+GPIOx_IS3L)	 /* GPIO Input register3 High or Low */
 
 
-/*----------------------------------------------------------------------------+
-  | Declare Configuration values
-  +----------------------------------------------------------------------------*/
-typedef enum gpio_select { GPIO_SEL, GPIO_ALT1, GPIO_ALT2, GPIO_ALT3 } gpio_select_t;
-typedef enum gpio_driver { GPIO_DIS, GPIO_IN, GPIO_OUT, GPIO_BI } gpio_driver_t;
-
-typedef struct { unsigned long	add;	/* gpio core base address */
-	gpio_driver_t  in_out; /* Driver Setting */
-	gpio_select_t  alt_nb; /* Selected Alternate */
-} gpio_param_s;
-
 /*----------------------------------------------------------------------------+
   |			XX     XX
   |

board/amcc/bamboo/config.mk

@@ -1,5 +1,5 @@
 #
-# (C) Copyright 2002
+# (C) Copyright 2002-2006
 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 #
 # See file CREDITS for list of people who contributed to this
@@ -21,7 +21,7 @@
 # MA 02111-1307 USA
 #
 
-TEXT_BASE = 0xFFF80000
+TEXT_BASE = 0xFFFA0000
 
 PLATFORM_CPPFLAGS += -DCONFIG_440=1
 

board/amcc/yellowstone/yellowstone.c

@@ -313,13 +313,13 @@ void sdram_init(void)
 	mtsdram(mem_tr0, 0x410a4012);	/* ?? */
 	mtsdram(mem_rtr, 0x04080000);	/* ?? */
 	mtsdram(mem_cfg1, 0x00000000);	/* Self-refresh exit, disable PM    */
-	mtsdram(mem_cfg0, 0x34000000);	/* Disable EEC */
+	mtsdram(mem_cfg0, 0x30000000);	/* Disable EEC */
 	udelay(400);		/* Delay 200 usecs (min)            */
 
 	/*--------------------------------------------------------------------
 	 * Enable the controller, then wait for DCEN to complete
 	 *------------------------------------------------------------------*/
-	mtsdram(mem_cfg0, 0x84000000);	/* Enable */
+	mtsdram(mem_cfg0, 0x80000000);	/* Enable */
 
 	for (;;) {
 		mfsdram(mem_mcsts, reg);

board/amcc/yosemite/yosemite.c

@@ -309,13 +309,13 @@ void sdram_init(void)
 	mtsdram(mem_tr0, 0x410a4012);	/* ?? */
 	mtsdram(mem_rtr, 0x04080000);	/* ?? */
 	mtsdram(mem_cfg1, 0x00000000);	/* Self-refresh exit, disable PM    */
-	mtsdram(mem_cfg0, 0x34000000);	/* Disable EEC */
+	mtsdram(mem_cfg0, 0x30000000);	/* Disable EEC */
 	udelay(400);		/* Delay 200 usecs (min)            */
 
 	/*--------------------------------------------------------------------
 	 * Enable the controller, then wait for DCEN to complete
 	 *------------------------------------------------------------------*/
-	mtsdram(mem_cfg0, 0x84000000);	/* Enable */
+	mtsdram(mem_cfg0, 0x80000000);	/* Enable */
 
 	for (;;) {
 		mfsdram(mem_mcsts, reg);

board/amcc/yucca/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o cmd_yucca.o
+SOBJS	= init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend *~
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/amcc/yucca/cmd_yucca.c

@@ -0,0 +1,288 @@
+/*
+ * (C) Copyright 2001
+ * Denis Peter, MPL AG Switzerland, d.peter@mpl.ch
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * hacked for evb440spe
+ */
+
+#include <common.h>
+#include <command.h>
+#include "yucca.h"
+#include <i2c.h>
+#include <asm/byteorder.h>
+
+extern void print_evb440spe_info(void);
+static int setBootStrapClock(cmd_tbl_t *cmdtp, int incrflag,
+		int flag, int argc, char *argv[]);
+
+extern int cmd_get_data_size(char* arg, int default_size);
+
+/* ------------------------------------------------------------------------- */
+int do_evb440spe(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	return setBootStrapClock (cmdtp, 1, flag, argc, argv);
+}
+
+/* ------------------------------------------------------------------------- */
+/* Modify memory.
+ *
+ * Syntax:
+ *	evb440spe wrclk prom0,prom1
+ */
+static int setBootStrapClock(cmd_tbl_t *cmdtp, int incrflag, int flag,
+		int argc, char *argv[])
+{
+	uchar	chip;
+	ulong	data;
+	int	nbytes;
+	extern char console_buffer[];
+
+	char sysClock[4];
+	char cpuClock[4];
+	char plbClock[4];
+	char pcixClock[4];
+
+	if (argc < 3) {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
+	if (strcmp(argv[2], "prom0") == 0)
+		chip = IIC0_BOOTPROM_ADDR;
+	else
+		chip = IIC0_ALT_BOOTPROM_ADDR;
+
+	do {
+		printf("enter sys clock frequency 33 or 66 Mhz or quit to abort\n");
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if ((strcmp(console_buffer, "33") != 0) &
+				(strcmp(console_buffer, "66") != 0))
+			nbytes=0;
+
+		strcpy(sysClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	do {
+		if (strcmp(sysClock, "66") == 0) {
+			printf("enter cpu clock frequency 400, 533 Mhz or quit to abort\n");
+		} else {
+#ifdef	CONFIG_STRESS
+			printf("enter cpu clock frequency 400, 500, 533, 667 Mhz or quit to abort\n");
+#else
+			printf("enter cpu clock frequency 400, 500, 533 Mhz or quit to abort\n");
+#endif
+		}
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if (strcmp(sysClock, "66") == 0) {
+			if ((strcmp(console_buffer, "400") != 0) &
+					(strcmp(console_buffer, "533") != 0)
+#ifdef	CONFIG_STRESS
+					& (strcmp(console_buffer, "667") != 0)
+#endif
+			   ) {
+				nbytes = 0;
+			}
+		} else {
+			if ((strcmp(console_buffer, "400") != 0) &
+					(strcmp(console_buffer, "500") != 0) &
+					(strcmp(console_buffer, "533") != 0)
+#ifdef	CONFIG_STRESS
+					& (strcmp(console_buffer, "667") != 0)
+#endif
+			   ) {
+				nbytes = 0;
+			}
+		}
+
+		strcpy(cpuClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	if (strcmp(cpuClock, "500") == 0){
+		strcpy(plbClock, "166");
+	} else if (strcmp(cpuClock, "533") == 0){
+		strcpy(plbClock, "133");
+	} else {
+		do {
+			if (strcmp(cpuClock, "400") == 0)
+				printf("enter plb clock frequency 100, 133 Mhz or quit to abort\n");
+
+#ifdef	CONFIG_STRESS
+			if (strcmp(cpuClock, "667") == 0)
+				printf("enter plb clock frequency 133, 166 Mhz or quit to abort\n");
+
+#endif
+			nbytes = readline (" ? ");
+
+			if (strcmp(console_buffer, "quit") == 0)
+				return 0;
+
+			if (strcmp(cpuClock, "400") == 0) {
+				if ((strcmp(console_buffer, "100") != 0) &
+						(strcmp(console_buffer, "133") != 0))
+					nbytes = 0;
+			}
+#ifdef	CONFIG_STRESS
+			if (strcmp(cpuClock, "667") == 0) {
+				if ((strcmp(console_buffer, "133") != 0) &
+						(strcmp(console_buffer, "166") != 0))
+					nbytes = 0;
+			}
+#endif
+			strcpy(plbClock, console_buffer);
+
+		} while (nbytes == 0);
+	}
+
+	do {
+		printf("enter Pci-X clock frequency 33, 66, 100 or 133 Mhz or quit to abort\n");
+		nbytes = readline (" ? ");
+
+		if (strcmp(console_buffer, "quit") == 0)
+			return 0;
+
+		if ((strcmp(console_buffer, "33") != 0) &
+				(strcmp(console_buffer, "66") != 0) &
+				(strcmp(console_buffer, "100") != 0) &
+				(strcmp(console_buffer, "133") != 0)) {
+			nbytes = 0;
+		}
+		strcpy(pcixClock, console_buffer);
+
+	} while (nbytes == 0);
+
+	printf("\nsys clk   = %sMhz\n", sysClock);
+	printf("cpu clk   = %sMhz\n", cpuClock);
+	printf("plb clk   = %sMhz\n", plbClock);
+	printf("Pci-X clk = %sMhz\n", pcixClock);
+
+	do {
+		printf("\npress [y] to write I2C bootstrap \n");
+		printf("or [n] to abort.  \n");
+		printf("Don't forget to set board switches \n");
+		printf("according to your choice before re-starting \n");
+		printf("(refer to 440spe_uboot_kit_um_1_01.pdf) \n");
+
+		nbytes = readline (" ? ");
+		if (strcmp(console_buffer, "n") == 0)
+			return 0;
+
+	} while (nbytes == 0);
+
+	if (strcmp(sysClock, "33") == 0) {
+		if ((strcmp(cpuClock, "400") == 0) &
+				(strcmp(plbClock, "100") == 0))
+			data = 0x8678c206;
+
+		if ((strcmp(cpuClock, "400") == 0) &
+				(strcmp(plbClock, "133") == 0))
+			data = 0x8678c2c6;
+
+		if ((strcmp(cpuClock, "500") == 0))
+			data = 0x8778f2c6;
+
+		if ((strcmp(cpuClock, "533") == 0))
+			data = 0x87790252;
+
+#ifdef	CONFIG_STRESS
+		if ((strcmp(cpuClock, "667") == 0) &
+				(strcmp(plbClock, "133") == 0))
+			data = 0x87794256;
+
+		if ((strcmp(cpuClock, "667") == 0) &
+				(strcmp(plbClock, "166") == 0))
+			data = 0x87794206;
+
+#endif
+	}
+	if (strcmp(sysClock, "66") == 0) {
+		if ((strcmp(cpuClock, "400") == 0) &
+				(strcmp(plbClock, "100") == 0))
+			data = 0x84706206;
+
+		if ((strcmp(cpuClock, "400") == 0) &
+				(strcmp(plbClock, "133") == 0))
+			data = 0x847062c6;
+
+		if ((strcmp(cpuClock, "533") == 0))
+			data = 0x85708206;
+
+#ifdef	CONFIG_STRESS
+		if ((strcmp(cpuClock, "667") == 0) &
+				(strcmp(plbClock, "133") == 0))
+			data = 0x8570a256;
+
+		if ((strcmp(cpuClock, "667") == 0) &
+				(strcmp(plbClock, "166") == 0))
+			data = 0x8570a206;
+
+#endif
+	}
+
+#ifdef	DEBUG
+	printf(" pin strap0 to write in i2c  = %x\n", data);
+#endif	/* DEBUG */
+
+	if (i2c_write(chip, 0, 1, (uchar *)&data, 4) != 0)
+		printf("Error writing strap0 in %s\n", argv[2]);
+
+	if (strcmp(pcixClock, "33") == 0)
+		data = 0x00000701;
+
+	if (strcmp(pcixClock, "66") == 0)
+		data = 0x00000601;
+
+	if (strcmp(pcixClock, "100") == 0)
+		data = 0x00000501;
+
+	if (strcmp(pcixClock, "133") == 0)
+		data = 0x00000401;
+
+	if (strcmp(plbClock, "166") == 0)
+		data = data | 0x05950000;
+	else
+		data = data | 0x05A50000;
+
+#ifdef	DEBUG
+	printf(" pin strap1 to write in i2c  = %x\n", data);
+#endif	/* DEBUG */
+
+	udelay(1000);
+	if (i2c_write(chip, 4, 1, (uchar *)&data, 4) != 0)
+		printf("Error writing strap1 in %s\n", argv[2]);
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	evb440spe,	3,	1,	do_evb440spe,
+	"evb440spe - program the serial device strap\n",
+	"wrclk [prom0|prom1] - program the serial device strap\n"
+);

board/amcc/yucca/config.mk

@@ -0,0 +1,42 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# AMCC 440SPe Reference Platform (yucca) board
+#
+
+ifeq ($(ramsym),1)
+TEXT_BASE = 0x07FD0000
+else
+TEXT_BASE = 0xfffb0000
+endif
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif

board/amcc/yucca/init.S

@@ -0,0 +1,104 @@
+/*
+ *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/* port to AMCC 440SPE evaluatioon board - SG April 12,2005  */
+
+#include <ppc_asm.tmpl>
+#include <config.h>
+
+/* General */
+#define TLB_VALID   0x00000200
+
+/* Supported page sizes */
+
+#define SZ_1K	0x00000000
+#define SZ_4K	0x00000010
+#define SZ_16K	0x00000020
+#define SZ_64K	0x00000030
+#define SZ_256K	0x00000040
+#define SZ_1M	0x00000050
+#define SZ_16M	0x00000070
+#define SZ_256M	0x00000090
+
+/* Storage attributes */
+#define SA_W	0x00000800	/* Write-through */
+#define SA_I	0x00000400	/* Caching inhibited */
+#define SA_M	0x00000200	/* Memory coherence */
+#define SA_G	0x00000100	/* Guarded */
+#define SA_E	0x00000080	/* Endian */
+
+/* Access control */
+#define AC_X	0x00000024	/* Execute */
+#define AC_W	0x00000012	/* Write */
+#define AC_R	0x00000009	/* Read */
+
+/* Some handy macros */
+
+#define EPN(e)		((e) & 0xfffffc00)
+#define TLB0(epn,sz)	((EPN((epn)) | (sz) | TLB_VALID ))
+#define TLB1(rpn,erpn)	(((rpn) & 0xfffffc00) | (erpn))
+#define TLB2(a)		((a) & 0x00000fbf)
+
+#define tlbtab_start\
+	mflr	r1	;\
+	bl	0f	;
+
+#define tlbtab_end\
+	.long 0, 0, 0	;\
+0:	mflr	r0	;\
+	mtlr	r1	;\
+	blr		;
+
+#define tlbentry(epn,sz,rpn,erpn,attr)\
+	.long TLB0(epn,sz),TLB1(rpn,erpn),TLB2(attr)
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+
+	.section .bootpg,"ax"
+	.globl tlbtab
+
+tlbtab:
+	tlbtab_start
+	tlbentry(0xfff00000, SZ_16M, 0xfff00000, 4, AC_R|AC_W|AC_X|SA_G)
+
+	tlbentry(CFG_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CFG_SDRAM_BASE + 0x10000000, SZ_256M, 0x10000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CFG_SDRAM_BASE + 0x20000000, SZ_256M, 0x20000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CFG_SDRAM_BASE + 0x30000000, SZ_256M, 0x30000000, 0, AC_R|AC_W|AC_X|SA_G|SA_I)
+
+	tlbentry(CFG_ISRAM_BASE, SZ_256K, 0x00000000, 4, AC_R|AC_W|AC_X|SA_I)
+	tlbentry(CFG_FPGA_BASE,SZ_1K, 0xE2000000, 4,AC_R|AC_W|SA_I)
+
+	tlbentry(CFG_OPER_FLASH,SZ_16M,0xE7000000, 4,AC_R|AC_W|AC_X|SA_G|SA_I)
+	tlbentry(CFG_PERIPHERAL_BASE, SZ_4K, 0xF0000000, 4, AC_R|AC_W|SA_G|SA_I)
+
+	tlbentry(CFG_PCI_BASE, SZ_256M, 0x00000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbentry(CFG_PCI_MEMBASE, SZ_256M, 0x10000000, 0xC, AC_R|AC_W|SA_G|SA_I)
+	tlbtab_end

board/amcc/yucca/u-boot.lds

@@ -0,0 +1,157 @@
+/*
+ * (C) Copyright 2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o		(.text)
+    board/amcc/yucca/init.o	(.text)
+    cpu/ppc4xx/kgdb.o		(.text)
+    cpu/ppc4xx/traps.o		(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o		(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o		(.text)
+    common/dlmalloc.o		(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o		(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    . = env_offset;*/
+/*    common/environment.o(.text)*/
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/amcc/yucca/u-boot.lds.debug

@@ -0,0 +1,146 @@
+/*
+ * (C) Copyright 2002-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text)	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data)	}
+  .rel.rodata    : { *(.rel.rodata)	}
+  .rela.rodata   : { *(.rela.rodata)	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o		(.text)
+    board/amcc/yucca/init.o	(.text)
+    cpu/ppc4xx/kgdb.o		(.text)
+    cpu/ppc4xx/traps.o		(.text)
+    cpu/ppc4xx/interrupts.o	(.text)
+    cpu/ppc4xx/serial.o		(.text)
+    cpu/ppc4xx/cpu_init.o	(.text)
+    cpu/ppc4xx/speed.o		(.text)
+    common/dlmalloc.o		(.text)
+    lib_generic/crc32.o		(.text)
+    lib_ppc/extable.o		(.text)
+    lib_generic/zlib.o		(.text)
+
+/*    common/environment.o(.text) */
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/amcc/yucca/yucca.h

@@ -0,0 +1,363 @@
+/*
+ * (C) Copyright 2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __YUCCA_H_
+#define __YUCCA_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/*----------------------------------------------------------------------------+
+| Defines
++----------------------------------------------------------------------------*/
+
+#define TMR_FREQ_EXT		25000000
+#define BOARD_UART_CLOCK	11059200
+
+#define BOARD_OPTION_SELECTED		1
+#define BOARD_OPTION_NOT_SELECTED	0
+
+#define ENGINEERING_CLOCK_CHECKING "clk_chk"
+#define ENGINEERING_EXTERNAL_CLOCK "ext_clk"
+
+#define ENGINEERING_CLOCK_CHECKING_DATA	1
+#define ENGINEERING_EXTERNAL_CLOCK_DATA	2
+
+/* ethernet definition */
+#define MAX_ENETMODE_PARM	3
+#define ENETMODE_NEG		0
+#define ENETMODE_SPEED		1
+#define ENETMODE_DUPLEX		2
+
+#define ENETMODE_AUTONEG	0
+#define ENETMODE_NO_AUTONEG	1
+#define ENETMODE_10		2
+#define ENETMODE_100		3
+#define ENETMODE_1000		4
+#define ENETMODE_HALF		5
+#define ENETMODE_FULL		6
+
+#define NUM_TLB_ENTRIES          64
+
+/*----------------------------------------------------------------------------+
+| TLB specific defines.
++----------------------------------------------------------------------------*/
+#define TLB_256MB_ALIGN_MASK	0xF0000000
+#define TLB_16MB_ALIGN_MASK	0xFF000000
+#define TLB_1MB_ALIGN_MASK	0xFFF00000
+#define TLB_256KB_ALIGN_MASK	0xFFFC0000
+#define TLB_64KB_ALIGN_MASK	0xFFFF0000
+#define TLB_16KB_ALIGN_MASK	0xFFFFC000
+#define TLB_4KB_ALIGN_MASK	0xFFFFF000
+#define TLB_1KB_ALIGN_MASK	0xFFFFFC00
+#define TLB_256MB_SIZE		0x10000000
+#define TLB_16MB_SIZE		0x01000000
+#define TLB_1MB_SIZE		0x00100000
+#define TLB_256KB_SIZE		0x00040000
+#define TLB_64KB_SIZE		0x00010000
+#define TLB_16KB_SIZE		0x00004000
+#define TLB_4KB_SIZE		0x00001000
+#define TLB_1KB_SIZE		0x00000400
+
+#define TLB_WORD0_EPN_MASK	0xFFFFFC00
+#define TLB_WORD0_EPN_ENCODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD0_EPN_DECODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD0_V_MASK	0x00000200
+#define TLB_WORD0_V_ENABLE	0x00000200
+#define TLB_WORD0_V_DISABLE	0x00000000
+#define TLB_WORD0_TS_MASK	0x00000100
+#define TLB_WORD0_TS_1		0x00000100
+#define TLB_WORD0_TS_0		0x00000000
+#define TLB_WORD0_SIZE_MASK	0x000000F0
+#define TLB_WORD0_SIZE_1KB	0x00000000
+#define TLB_WORD0_SIZE_4KB	0x00000010
+#define TLB_WORD0_SIZE_16KB	0x00000020
+#define TLB_WORD0_SIZE_64KB	0x00000030
+#define TLB_WORD0_SIZE_256KB	0x00000040
+#define TLB_WORD0_SIZE_1MB	0x00000050
+#define TLB_WORD0_SIZE_16MB	0x00000070
+#define TLB_WORD0_SIZE_256MB	0x00000090
+#define TLB_WORD0_TPAR_MASK	0x0000000F
+#define TLB_WORD0_TPAR_ENCODE(n) ((((unsigned long)(n))&0x0F)<<0)
+#define TLB_WORD0_TPAR_DECODE(n) ((((unsigned long)(n))>>0)&0x0F)
+
+#define TLB_WORD1_RPN_MASK	0xFFFFFC00
+#define TLB_WORD1_RPN_ENCODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD1_RPN_DECODE(n) (((unsigned long)(n))&0xFFFFFC00)
+#define TLB_WORD1_PAR1_MASK	0x00000300
+#define TLB_WORD1_PAR1_ENCODE(n) ((((unsigned long)(n))&0x03)<<8)
+#define TLB_WORD1_PAR1_DECODE(n) ((((unsigned long)(n))>>8)&0x03)
+#define TLB_WORD1_PAR1_0	0x00000000
+#define TLB_WORD1_PAR1_1	0x00000100
+#define TLB_WORD1_PAR1_2	0x00000200
+#define TLB_WORD1_PAR1_3	0x00000300
+#define TLB_WORD1_ERPN_MASK	0x0000000F
+#define TLB_WORD1_ERPN_ENCODE(n) ((((unsigned long)(n))&0x0F)<<0)
+#define TLB_WORD1_ERPN_DECODE(n) ((((unsigned long)(n))>>0)&0x0F)
+
+#define TLB_WORD2_PAR2_MASK	0xC0000000
+#define TLB_WORD2_PAR2_ENCODE(n) ((((unsigned long)(n))&0x03)<<30)
+#define TLB_WORD2_PAR2_DECODE(n) ((((unsigned long)(n))>>30)&0x03)
+#define TLB_WORD2_PAR2_0	0x00000000
+#define TLB_WORD2_PAR2_1	0x40000000
+#define TLB_WORD2_PAR2_2	0x80000000
+#define TLB_WORD2_PAR2_3	0xC0000000
+#define TLB_WORD2_U0_MASK	0x00008000
+#define TLB_WORD2_U0_ENABLE	0x00008000
+#define TLB_WORD2_U0_DISABLE	0x00000000
+#define TLB_WORD2_U1_MASK	0x00004000
+#define TLB_WORD2_U1_ENABLE	0x00004000
+#define TLB_WORD2_U1_DISABLE	0x00000000
+#define TLB_WORD2_U2_MASK	0x00002000
+#define TLB_WORD2_U2_ENABLE	0x00002000
+#define TLB_WORD2_U2_DISABLE	0x00000000
+#define TLB_WORD2_U3_MASK	0x00001000
+#define TLB_WORD2_U3_ENABLE	0x00001000
+#define TLB_WORD2_U3_DISABLE	0x00000000
+#define TLB_WORD2_W_MASK	0x00000800
+#define TLB_WORD2_W_ENABLE	0x00000800
+#define TLB_WORD2_W_DISABLE	0x00000000
+#define TLB_WORD2_I_MASK	0x00000400
+#define TLB_WORD2_I_ENABLE	0x00000400
+#define TLB_WORD2_I_DISABLE	0x00000000
+#define TLB_WORD2_M_MASK	0x00000200
+#define TLB_WORD2_M_ENABLE	0x00000200
+#define TLB_WORD2_M_DISABLE	0x00000000
+#define TLB_WORD2_G_MASK	0x00000100
+#define TLB_WORD2_G_ENABLE	0x00000100
+#define TLB_WORD2_G_DISABLE	0x00000000
+#define TLB_WORD2_E_MASK	0x00000080
+#define TLB_WORD2_E_ENABLE	0x00000080
+#define TLB_WORD2_E_DISABLE	0x00000000
+#define TLB_WORD2_UX_MASK	0x00000020
+#define TLB_WORD2_UX_ENABLE	0x00000020
+#define TLB_WORD2_UX_DISABLE	0x00000000
+#define TLB_WORD2_UW_MASK	0x00000010
+#define TLB_WORD2_UW_ENABLE	0x00000010
+#define TLB_WORD2_UW_DISABLE	0x00000000
+#define TLB_WORD2_UR_MASK	0x00000008
+#define TLB_WORD2_UR_ENABLE	0x00000008
+#define TLB_WORD2_UR_DISABLE	0x00000000
+#define TLB_WORD2_SX_MASK	0x00000004
+#define TLB_WORD2_SX_ENABLE	0x00000004
+#define TLB_WORD2_SX_DISABLE	0x00000000
+#define TLB_WORD2_SW_MASK	0x00000002
+#define TLB_WORD2_SW_ENABLE	0x00000002
+#define TLB_WORD2_SW_DISABLE	0x00000000
+#define TLB_WORD2_SR_MASK	0x00000001
+#define TLB_WORD2_SR_ENABLE	0x00000001
+#define TLB_WORD2_SR_DISABLE	0x00000000
+
+/*----------------------------------------------------------------------------+
+| Board specific defines.
++----------------------------------------------------------------------------*/
+#define NONCACHE_MEMORY_SIZE     (64*1024)
+#define NONCACHE_AREA0_ENDOFFSET (64*1024)
+#define NONCACHE_AREA1_ENDOFFSET (32*1024)
+
+#define FLASH_SECTORSIZE	0x00010000
+
+/* SDRAM MICRON */
+#define SDRAM_MICRON		0x2C
+
+#define SDRAM_TRUE		1
+#define SDRAM_FALSE		0
+#define SDRAM_DDR1		1
+#define SDRAM_DDR2		2
+#define SDRAM_NONE		0
+#define MAXDIMMS		2		/* Changes le 12/01/05 pour 1.6 */
+#define MAXRANKS		4		/* Changes le 12/01/05 pour 1.6 */
+#define MAXBANKSPERDIMM		2
+#define MAXRANKSPERDIMM		2
+#define MAXBXCF			4		/* Changes le 12/01/05 pour 1.6 */
+#define MAXSDRAMMEMORY		0xFFFFFFFF	/* 4GB */
+#define ERROR_STR_LENGTH	256
+#define MAX_SPD_BYTES		256		/* Max number of bytes on the DIMM's SPD EEPROM */
+
+/*----------------------------------------------------------------------------+
+| SDR Configuration registers
++----------------------------------------------------------------------------*/
+/* Serial Device Strap Reg 0 */
+#define sdr_pstrp0	0x0040
+
+#define	SDR0_SDSTP1_EBC_ROM_BS_MASK	0x00000080 /* EBC Boot bus width Mask */
+#define	SDR0_SDSTP1_EBC_ROM_BS_16BIT	0x00000080 /* EBC 16 Bits */
+#define	SDR0_SDSTP1_EBC_ROM_BS_8BIT	0x00000000 /* EBC  8 Bits */
+
+#define	SDR0_SDSTP1_BOOT_SEL_MASK	0x00080000 /* Boot device Selection Mask */
+#define	SDR0_SDSTP1_BOOT_SEL_EBC	0x00000000 /* EBC */
+#define	SDR0_SDSTP1_BOOT_SEL_PCI	0x00080000 /* PCI */
+
+#define	SDR0_SDSTP1_EBC_SIZE_MASK	0x00000060 /* Boot rom size Mask */
+#define	SDR0_SDSTP1_BOOT_SIZE_16MB	0x00000060 /* 16 MB */
+#define	SDR0_SDSTP1_BOOT_SIZE_8MB	0x00000040 /*  8 MB */
+#define	SDR0_SDSTP1_BOOT_SIZE_4MB	0x00000020 /*  4 MB */
+#define	SDR0_SDSTP1_BOOT_SIZE_2MB	0x00000000 /*  2 MB */
+
+/* Serial Device Enabled - Addr = 0xA8 */
+#define SDR0_PSTRP0_BOOTSTRAP_IIC_A8_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS5
+/* Serial Device Enabled - Addr = 0xA4 */
+#define SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN SDR0_PSTRP0_BOOTSTRAP_SETTINGS7
+
+/* Pin Straps Reg */
+#define SDR0_PSTRP0			0x0040
+#define SDR0_PSTRP0_BOOTSTRAP_MASK	0xE0000000  /* Strap Bits */
+
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS0	0x00000000  /* Default strap settings 0 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS1	0x20000000  /* Default strap settings 1 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS2	0x40000000  /* Default strap settings 2 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS3	0x60000000  /* Default strap settings 3 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS4	0x80000000  /* Default strap settings 4 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS5	0xA0000000  /* Default strap settings 5 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS6	0xC0000000  /* Default strap settings 6 */
+#define SDR0_PSTRP0_BOOTSTRAP_SETTINGS7	0xE0000000  /* Default strap settings 7 */
+
+/* fpgareg - defines are in include/config/YUCCA.h */
+
+#define SDR0_CUST0_ENET3_MASK		0x00000080
+#define SDR0_CUST0_ENET3_COPPER		0x00000000
+#define SDR0_CUST0_ENET3_FIBER		0x00000080
+#define SDR0_CUST0_RGMII3_MASK		0x00000070
+#define SDR0_CUST0_RGMII3_ENCODE(n)	((((unsigned long)(n))&0x7)<<4)
+#define SDR0_CUST0_RGMII3_DECODE(n)	((((unsigned long)(n))>>4)&0x07)
+#define SDR0_CUST0_RGMII3_DISAB		0x00000000
+#define SDR0_CUST0_RGMII3_RTBI		0x00000040
+#define SDR0_CUST0_RGMII3_RGMII		0x00000050
+#define SDR0_CUST0_RGMII3_TBI		0x00000060
+#define SDR0_CUST0_RGMII3_GMII		0x00000070
+#define SDR0_CUST0_ENET2_MASK		0x00000008
+#define SDR0_CUST0_ENET2_COPPER		0x00000000
+#define SDR0_CUST0_ENET2_FIBER		0x00000008
+#define SDR0_CUST0_RGMII2_MASK		0x00000007
+#define SDR0_CUST0_RGMII2_ENCODE(n)	((((unsigned long)(n))&0x7)<<0)
+#define SDR0_CUST0_RGMII2_DECODE(n)	((((unsigned long)(n))>>0)&0x07)
+#define SDR0_CUST0_RGMII2_DISAB		0x00000000
+#define SDR0_CUST0_RGMII2_RTBI		0x00000004
+#define SDR0_CUST0_RGMII2_RGMII		0x00000005
+#define SDR0_CUST0_RGMII2_TBI		0x00000006
+#define SDR0_CUST0_RGMII2_GMII		0x00000007
+
+#define ONE_MILLION			1000000
+#define ONE_BILLION			1000000000
+
+/*----------------------------------------------------------------------------+
+|                               X
+|                              XX
+| XX  XXX   XXXXX   XX XXX    XXXXX
+| XX  XX        X    XXX XX    XX
+| XX  XX   XXXXXX    XX        XX
+| XX  XX   X   XX    XX        XX XX
+|  XXX XX  XXXXX X  XXXX        XXX
++----------------------------------------------------------------------------*/
+/*----------------------------------------------------------------------------+
+| Declare Configuration values
++----------------------------------------------------------------------------*/
+
+typedef enum config_selection {
+	CONFIG_NOT_SELECTED,
+	CONFIG_SELECTED
+} config_selection_t;
+
+typedef enum config_list {
+	UART2_IN_SERVICE_MODE,
+	CPU_TRACE_MODE,
+	UART1_CTS_RTS,
+	CONFIG_NB
+} config_list_t;
+
+#define MAX_CONFIG_SELECT_NB			3
+
+#define BOARD_INFO_UART2_IN_SERVICE_MODE	1
+#define BOARD_INFO_CPU_TRACE_MODE		2
+#define BOARD_INFO_UART1_CTS_RTS_MODE		4
+
+void force_bup_config_selection(config_selection_t *confgi_select_P);
+void update_config_selection_table(config_selection_t *config_select_P);
+void display_config_selection(config_selection_t *config_select_P);
+
+/*----------------------------------------------------------------------------+
+|                     XX
+|
+|   XXXX    XX XXX   XXX     XXXX
+|  XX        XX  XX   XX    XX  XX
+|  XX  XXX   XX  XX   XX    XX  XX
+|  XX  XX    XXXXX    XX    XX  XX
+|   XXXX     XX      XXXX    XXXX
+|           XXXX
+|
+|
+|
+| +------------------------------------------------------------------+
+| |  GPIO/Secondary func | Primary Function | I/O | Alternate1 | I/O |
+| +----------------------+------------------+-----+------------+-----+
+| |                      |                  |     |            |     |
+| | GPIO0_0              | PCIX0REQ2_N      | I/O |  TRCCLK    |     |
+| | GPIO0_1              | PCIX0REQ3_N      | I/O |  TRCBS0    |     |
+| | GPIO0_2              | PCIX0GNT2_N      | I/O |  TRCBS1    |     |
+| | GPIO0_3              | PCIX0GNT3_N      | I/O |  TRCBS2    |     |
+| | GPIO0_4              | PCIX1REQ2_N      | I/O |  TRCES0    |     |
+| | GPIO0_5              | PCIX1REQ3_N      | I/O |  TRCES1    |     |
+| | GPIO0_6              | PCIX1GNT2_N      | I/O |  TRCES2    | NA  |
+| | GPIO0_7              | PCIX1GNT3_N      | I/O |  TRCES3    | NA  |
+| | GPIO0_8              | PERREADY         |  I  |  TRCES4    | NA  |
+| | GPIO0_9              | PERCS1_N         |  O  |  TRCTS0    | NA  |
+| | GPIO0_10             | PERCS2_N         |  O  |  TRCTS1    | NA  |
+| | GPIO0_11             | IRQ0             |  I  |  TRCTS2    | NA  |
+| | GPIO0_12             | IRQ1             |  I  |  TRCTS3    | NA  |
+| | GPIO0_13             | IRQ2             |  I  |  TRCTS4    | NA  |
+| | GPIO0_14             | IRQ3             |  I  |  TRCTS5    | NA  |
+| | GPIO0_15             | IRQ4             |  I  |  TRCTS6    | NA  |
+| | GPIO0_16             | IRQ5             |  I  |  UART2RX   |  I  |
+| | GPIO0_17             | PERBE0_N         |  O  |  UART2TX   |  O  |
+| | GPIO0_18             | PCI0GNT0_N       | I/O |  NA        | NA  |
+| | GPIO0_19             | PCI0GNT1_N       | I/O |  NA        | NA  |
+| | GPIO0_20             | PCI0REQ0_N       | I/O |  NA        | NA  |
+| | GPIO0_21             | PCI0REQ1_N       | I/O |  NA        | NA  |
+| | GPIO0_22             | PCI1GNT0_N       | I/O |  NA        | NA  |
+| | GPIO0_23             | PCI1GNT1_N       | I/O |  NA        | NA  |
+| | GPIO0_24             | PCI1REQ0_N       | I/O |  NA        | NA  |
+| | GPIO0_25             | PCI1REQ1_N       | I/O |  NA        | NA  |
+| | GPIO0_26             | PCI2GNT0_N       | I/O |  NA        | NA  |
+| | GPIO0_27             | PCI2GNT1_N       | I/O |  NA        | NA  |
+| | GPIO0_28             | PCI2REQ0_N       | I/O |  NA        | NA  |
+| | GPIO0_29             | PCI2REQ1_N       | I/O |  NA        | NA  |
+| | GPIO0_30             | UART1RX          |  I  |  NA        | NA  |
+| | GPIO0_31             | UART1TX          |  O  |  NA        | NA  |
+| |                      |                  |     |            |     |
+| +----------------------+------------------+-----+------------+-----+
+|
++----------------------------------------------------------------------------*/
+
+unsigned long auto_calc_speed(void);
+/*----------------------------------------------------------------------------+
+| Prototypes
++----------------------------------------------------------------------------*/
+void print_evb440spe_info(void);
+
+int onboard_pci_arbiter_selected(int core_pci);
+
+#ifdef __cplusplus
+}
+#endif
+#endif /* __YUCCA_H_ */

board/atc/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o ti113x.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/atc/ti113x.c

@@ -0,0 +1,637 @@
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ ********************************************************************
+ *
+ * Lots of code copied from:
+ *
+ * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
+ * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
+ * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
+ */
+
+#include <common.h>
+
+#ifdef CONFIG_I82365
+
+#include <command.h>
+#include <pci.h>
+#include <pcmcia.h>
+#include <asm/io.h>
+
+#include <pcmcia/ss.h>
+#include <pcmcia/i82365.h>
+#include <pcmcia/yenta.h>
+#include <pcmcia/ti113x.h>
+
+static struct pci_device_id supported[] = {
+	{PCI_VENDOR_ID_TI, PCI_DEVICE_ID_TI_1510},
+	{0, 0}
+};
+
+#define CYCLE_TIME	120
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev);
+#endif
+
+typedef struct socket_info_t {
+	pci_dev_t	dev;
+	u_short		bcr;
+	u_char		pci_lat, cb_lat, sub_bus, cache;
+	u_int		cb_phys;
+
+	socket_cap_t	cap;
+	u_short		type;
+	u_int		flags;
+	ti113x_state_t	state;
+} socket_info_t;
+
+static socket_info_t socket;
+static socket_state_t state;
+static struct pccard_mem_map mem;
+static struct pccard_io_map io;
+
+/*====================================================================*/
+
+/* Some PCI shortcuts */
+
+static int pci_readb (socket_info_t * s, int r, u_char * v)
+{
+	return pci_read_config_byte (s->dev, r, v);
+}
+static int pci_writeb (socket_info_t * s, int r, u_char v)
+{
+	return pci_write_config_byte (s->dev, r, v);
+}
+static int pci_readw (socket_info_t * s, int r, u_short * v)
+{
+	return pci_read_config_word (s->dev, r, v);
+}
+static int pci_writew (socket_info_t * s, int r, u_short v)
+{
+	return pci_write_config_word (s->dev, r, v);
+}
+static int pci_readl (socket_info_t * s, int r, u_int * v)
+{
+	return pci_read_config_dword (s->dev, r, v);
+}
+static int pci_writel (socket_info_t * s, int r, u_int v)
+{
+	return pci_write_config_dword (s->dev, r, v);
+}
+
+/*====================================================================*/
+
+#define cb_readb(s, r)		readb((s)->cb_phys + (r))
+#define cb_readl(s, r)		readl((s)->cb_phys + (r))
+#define cb_writeb(s, r, v)	writeb(v, (s)->cb_phys + (r))
+#define cb_writel(s, r, v)	writel(v, (s)->cb_phys + (r))
+
+static u_char i365_get (socket_info_t * s, u_short reg)
+{
+	return cb_readb (s, 0x0800 + reg);
+}
+
+static void i365_set (socket_info_t * s, u_short reg, u_char data)
+{
+	cb_writeb (s, 0x0800 + reg, data);
+}
+
+static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) | mask);
+}
+
+static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) & ~mask);
+}
+
+#if 0	/* not used */
+static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
+{
+	u_char d = i365_get (s, reg);
+
+	i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
+}
+
+static u_short i365_get_pair (socket_info_t * s, u_short reg)
+{
+	return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
+}
+#endif	/* not used */
+
+static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
+{
+	i365_set (s, reg, data & 0xff);
+	i365_set (s, reg + 1, data >> 8);
+}
+
+/*======================================================================
+
+    Code to save and restore global state information for TI 1130 and
+    TI 1131 controllers, and to set and report global configuration
+    options.
+
+======================================================================*/
+
+static void ti113x_get_state (socket_info_t * s)
+{
+	ti113x_state_t *p = &s->state;
+
+	pci_readl (s, TI113X_SYSTEM_CONTROL, &p->sysctl);
+	pci_readb (s, TI113X_CARD_CONTROL, &p->cardctl);
+	pci_readb (s, TI113X_DEVICE_CONTROL, &p->devctl);
+	pci_readb (s, TI1250_DIAGNOSTIC, &p->diag);
+	pci_readl (s, TI12XX_IRQMUX, &p->irqmux);
+}
+
+static void ti113x_set_state (socket_info_t * s)
+{
+	ti113x_state_t *p = &s->state;
+
+	pci_writel (s, TI113X_SYSTEM_CONTROL, p->sysctl);
+	pci_writeb (s, TI113X_CARD_CONTROL, p->cardctl);
+	pci_writeb (s, TI113X_DEVICE_CONTROL, p->devctl);
+	pci_writeb (s, TI1250_MULTIMEDIA_CTL, 0);
+	pci_writeb (s, TI1250_DIAGNOSTIC, p->diag);
+	pci_writel (s, TI12XX_IRQMUX, p->irqmux);
+	i365_set_pair (s, TI113X_IO_OFFSET (0), 0);
+	i365_set_pair (s, TI113X_IO_OFFSET (1), 0);
+}
+
+static u_int ti113x_set_opts (socket_info_t * s)
+{
+	ti113x_state_t *p = &s->state;
+	u_int mask = 0xffff;
+
+	p->cardctl &= ~TI113X_CCR_ZVENABLE;
+	p->cardctl |= TI113X_CCR_SPKROUTEN;
+
+	return mask;
+}
+
+/*======================================================================
+
+    Routines to handle common CardBus options
+
+======================================================================*/
+
+/* Default settings for PCI command configuration register */
+#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
+		  PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
+
+static void cb_get_state (socket_info_t * s)
+{
+	pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
+	pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
+	pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
+	pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
+	pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
+	pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
+}
+
+static void cb_set_state (socket_info_t * s)
+{
+	pci_writel (s, CB_LEGACY_MODE_BASE, 0);
+	pci_writel (s, PCI_BASE_ADDRESS_0, s->cb_phys);
+	pci_writew (s, PCI_COMMAND, CMD_DFLT);
+	pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
+	pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
+	pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
+	pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
+	pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
+	pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
+}
+
+static void cb_set_opts (socket_info_t * s)
+{
+	if (s->cache == 0)
+		s->cache = 8;
+	if (s->pci_lat == 0)
+		s->pci_lat = 0xa8;
+	if (s->cb_lat == 0)
+		s->cb_lat = 0xb0;
+}
+
+/*======================================================================
+
+    Power control for Cardbus controllers: used both for 16-bit and
+    Cardbus cards.
+
+======================================================================*/
+
+static int cb_set_power (socket_info_t * s, socket_state_t * state)
+{
+	u_int reg = 0;
+
+	/* restart card voltage detection if it seems appropriate */
+	if ((state->Vcc == 0) && (state->Vpp == 0) &&
+	   !(cb_readl (s, CB_SOCKET_STATE) & CB_SS_VSENSE))
+		cb_writel (s, CB_SOCKET_FORCE, CB_SF_CVSTEST);
+	switch (state->Vcc) {
+	case 0:
+		reg = 0;
+		break;
+	case 33:
+		reg = CB_SC_VCC_3V;
+		break;
+	case 50:
+		reg = CB_SC_VCC_5V;
+		break;
+	default:
+		return -1;
+	}
+	switch (state->Vpp) {
+	case 0:
+		break;
+	case 33:
+		reg |= CB_SC_VPP_3V;
+		break;
+	case 50:
+		reg |= CB_SC_VPP_5V;
+		break;
+	case 120:
+		reg |= CB_SC_VPP_12V;
+		break;
+	default:
+		return -1;
+	}
+	if (reg != cb_readl (s, CB_SOCKET_CONTROL))
+		cb_writel (s, CB_SOCKET_CONTROL, reg);
+
+	return 0;
+}
+
+/*======================================================================
+
+    Generic routines to get and set controller options
+
+======================================================================*/
+
+static void get_bridge_state (socket_info_t * s)
+{
+	ti113x_get_state (s);
+	cb_get_state (s);
+}
+
+static void set_bridge_state (socket_info_t * s)
+{
+	cb_set_state (s);
+	i365_set (s, I365_GBLCTL, 0x00);
+	i365_set (s, I365_GENCTL, 0x00);
+	ti113x_set_state (s);
+}
+
+static void set_bridge_opts (socket_info_t * s)
+{
+	ti113x_set_opts (s);
+	cb_set_opts (s);
+}
+
+/*====================================================================*/
+#define PD67_EXT_INDEX		0x2e	/* Extension index */
+#define PD67_EXT_DATA		0x2f	/* Extension data */
+#define PD67_EXD_VS1(s)		(0x01 << ((s)<<1))
+
+#define pd67_ext_get(s, r) \
+    (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
+
+static int i365_get_status (socket_info_t * s, u_int * value)
+{
+	u_int status;
+
+	status = i365_get (s, I365_IDENT);
+	status = i365_get (s, I365_STATUS);
+	*value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
+	if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
+		*value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
+	} else {
+		*value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
+		*value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
+	}
+	*value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
+	*value |= (status & I365_CS_READY) ? SS_READY : 0;
+	*value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
+
+	status = cb_readl (s, CB_SOCKET_STATE);
+	*value |= (status & CB_SS_32BIT) ? SS_CARDBUS : 0;
+	*value |= (status & CB_SS_3VCARD) ? SS_3VCARD : 0;
+	*value |= (status & CB_SS_XVCARD) ? SS_XVCARD : 0;
+	*value |= (status & CB_SS_VSENSE) ? 0 : SS_PENDING;
+	/* For now, ignore cards with unsupported voltage keys */
+	if (*value & SS_XVCARD)
+		*value &= ~(SS_DETECT | SS_3VCARD | SS_XVCARD);
+
+	return 0;
+}	/* i365_get_status */
+
+static int i365_set_socket (socket_info_t * s, socket_state_t * state)
+{
+	u_char reg;
+
+	set_bridge_state (s);
+
+	/* IO card, RESET flag */
+	reg = 0;
+	reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
+	reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
+	i365_set (s, I365_INTCTL, reg);
+
+	reg = I365_PWR_NORESET;
+	if (state->flags & SS_PWR_AUTO)
+		reg |= I365_PWR_AUTO;
+	if (state->flags & SS_OUTPUT_ENA)
+		reg |= I365_PWR_OUT;
+
+	cb_set_power (s, state);
+	reg |= i365_get (s, I365_POWER) & (I365_VCC_MASK | I365_VPP1_MASK);
+
+	if (reg != i365_get (s, I365_POWER))
+		i365_set (s, I365_POWER, reg);
+
+	return 0;
+}	/* i365_set_socket */
+
+/*====================================================================*/
+
+static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
+{
+	u_short base, i;
+	u_char map;
+
+	debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
+		mem->map, mem->flags, mem->speed,
+		mem->sys_start, mem->sys_stop, mem->card_start);
+
+	map = mem->map;
+	if ((map > 4) ||
+	    (mem->card_start > 0x3ffffff) ||
+	    (mem->sys_start > mem->sys_stop) ||
+	    (mem->speed > 1000)) {
+		return -1;
+	}
+
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
+
+	/* Take care of high byte, for PCI controllers */
+	i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
+
+	base = I365_MEM (map);
+	i = (mem->sys_start >> 12) & 0x0fff;
+	if (mem->flags & MAP_16BIT)
+		i |= I365_MEM_16BIT;
+	if (mem->flags & MAP_0WS)
+		i |= I365_MEM_0WS;
+	i365_set_pair (s, base + I365_W_START, i);
+
+	i = (mem->sys_stop >> 12) & 0x0fff;
+	switch (mem->speed / CYCLE_TIME) {
+	case 0:
+		break;
+	case 1:
+		i |= I365_MEM_WS0;
+		break;
+	case 2:
+		i |= I365_MEM_WS1;
+		break;
+	default:
+		i |= I365_MEM_WS1 | I365_MEM_WS0;
+		break;
+	}
+	i365_set_pair (s, base + I365_W_STOP, i);
+
+	i = ((mem->card_start - mem->sys_start) >> 12) & 0x3fff;
+	if (mem->flags & MAP_WRPROT)
+		i |= I365_MEM_WRPROT;
+	if (mem->flags & MAP_ATTRIB)
+		i |= I365_MEM_REG;
+	i365_set_pair (s, base + I365_W_OFF, i);
+
+	/* Turn on the window if necessary */
+	if (mem->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
+	return 0;
+}	/* i365_set_mem_map */
+
+static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
+{
+	u_char map, ioctl;
+
+	map = io->map;
+	/* comment out: comparison is always false due to limited range of data type */
+	if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
+	    (io->stop < io->start))
+		return -1;
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
+	i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
+	i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
+	ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
+	if (io->speed)
+		ioctl |= I365_IOCTL_WAIT (map);
+	if (io->flags & MAP_0WS)
+		ioctl |= I365_IOCTL_0WS (map);
+	if (io->flags & MAP_16BIT)
+		ioctl |= I365_IOCTL_16BIT (map);
+	if (io->flags & MAP_AUTOSZ)
+		ioctl |= I365_IOCTL_IOCS16 (map);
+	i365_set (s, I365_IOCTL, ioctl);
+	/* Turn on the window if necessary */
+	if (io->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
+	return 0;
+}	/* i365_set_io_map */
+
+/*====================================================================*/
+
+int i82365_init (void)
+{
+	u_int val;
+	int i;
+
+	if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
+		/* Controller not found */
+		return 1;
+	}
+	debug ("i82365 Device Found!\n");
+
+	pci_read_config_dword (socket.dev, PCI_BASE_ADDRESS_0, &socket.cb_phys);
+	socket.cb_phys &= ~0xf;
+
+	get_bridge_state (&socket);
+	set_bridge_opts (&socket);
+
+	i = i365_get_status (&socket, &val);
+
+	if (val & SS_DETECT) {
+		if (val & SS_3VCARD) {
+			state.Vcc = state.Vpp = 33;
+			puts (" 3.3V card found: ");
+		} else if (!(val & SS_XVCARD)) {
+			state.Vcc = state.Vpp = 50;
+			puts (" 5.0V card found: ");
+		} else {
+			puts ("i82365: unsupported voltage key\n");
+			state.Vcc = state.Vpp = 0;
+		}
+	} else {
+		/* No card inserted */
+		puts ("No card\n");
+		return 1;
+	}
+
+	state.flags = SS_IOCARD | SS_OUTPUT_ENA;
+	state.csc_mask = 0;
+	state.io_irq = 0;
+
+	i365_set_socket (&socket, &state);
+
+	for (i = 500; i; i--) {
+		if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
+			break;
+		udelay (1000);
+	}
+
+	if (i == 0) {
+		/* PC Card not ready for data transfer */
+		puts ("i82365 PC Card not ready for data transfer\n");
+		return 1;
+	}
+	debug (" PC Card ready for data transfer: ");
+
+	mem.map = 0;
+	mem.flags = MAP_ATTRIB | MAP_ACTIVE;
+	mem.speed = 300;
+	mem.sys_start = CFG_PCMCIA_MEM_ADDR;
+	mem.sys_stop = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE - 1;
+	mem.card_start = 0;
+	i365_set_mem_map (&socket, &mem);
+
+	io.map = 0;
+	io.flags = MAP_AUTOSZ | MAP_ACTIVE;
+	io.speed = 0;
+	io.start = 0x0100;
+	io.stop = 0x010F;
+	i365_set_io_map (&socket, &io);
+
+#ifdef DEBUG
+	i82365_dump_regions (socket.dev);
+#endif
+
+	return 0;
+}
+
+void i82365_exit (void)
+{
+	io.map = 0;
+	io.flags = 0;
+	io.speed = 0;
+	io.start = 0;
+	io.stop = 0x1;
+
+	i365_set_io_map (&socket, &io);
+
+	mem.map = 0;
+	mem.flags = 0;
+	mem.speed = 0;
+	mem.sys_start = 0;
+	mem.sys_stop = 0x1000;
+	mem.card_start = 0;
+
+	i365_set_mem_map (&socket, &mem);
+
+	socket.state.sysctl &= 0xFFFF00FF;
+
+	state.Vcc = state.Vpp = 0;
+
+	i365_set_socket (&socket, &state);
+}
+
+int pcmcia_on (void)
+{
+	u_int rc;
+
+	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	rc = i82365_init();
+	if (rc)
+		goto exit;
+
+	rc = check_ide_device(0);
+	if (rc == 0)
+		goto exit;
+
+	i82365_exit();
+
+exit:
+	return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	i82365_exit();
+
+	return 0;
+}
+#endif
+
+/*======================================================================
+
+    Debug stuff
+
+======================================================================*/
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev)
+{
+	u_int tmp[2];
+	u_int *mem = (void *) socket.cb_phys;
+	u_char *cis = (void *) CFG_PCMCIA_MEM_ADDR;
+	u_char *ide = (void *) (CFG_ATA_BASE_ADDR + CFG_ATA_REG_OFFSET);
+
+	pci_read_config_dword (dev, 0x00, tmp + 0);
+	pci_read_config_dword (dev, 0x80, tmp + 1);
+
+	printf ("PCI CONF: %08X ... %08X\n",
+		tmp[0], tmp[1]);
+	printf ("PCI MEM:  ... %08X ... %08X\n",
+		mem[0x8 / 4], mem[0x800 / 4]);
+	printf ("CIS:      ...%c%c%c%c%c%c%c%c...\n",
+		cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
+		cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
+	printf ("CIS CONF: %02X %02X %02X ...\n",
+		cis[0x200], cis[0x202], cis[0x204]);
+	printf ("IDE:      %02X %02X %02X %02X %02X %02X %02X %02X\n",
+		ide[0], ide[1], ide[2], ide[3],
+		ide[4], ide[5], ide[6], ide[7]);
+}
+#endif	/* DEBUG */
+
+#endif /* CONFIG_I82365 */

board/c2mon/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/c2mon/pcmcia.c

@@ -0,0 +1,284 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "C2MON"
+
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	ushort sreg;
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure Port C for TPS2211 PC-Card Power-Interface Switch
+	*
+	* Switch off all voltages, assert shutdown
+	*/
+	sreg = immap->im_ioport.iop_pcdat;
+	sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1);	/* VAVPP => Hi-Z */
+	sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1);	/* 3V and 5V off */
+	immap->im_ioport.iop_pcdat = sreg;
+
+	immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
+	immap->im_ioport.iop_pcdir |=   TPS2211_OUTPUTS;
+
+	debug ("Set Port C: PAR:     %04x DIR:     %04x DAT:     %04x\n",
+	       immap->im_ioport.iop_pcpar,
+	       immap->im_ioport.iop_pcdir,
+	       immap->im_ioport.iop_pcdat);
+
+	/*
+	* Configure Port B for TPS2211 PC-Card Power-Interface Switch
+	*
+	* Over-Current Input only
+	*/
+	cp->cp_pbpar &= ~(TPS2211_INPUTS);
+	cp->cp_pbdir &= ~(TPS2211_INPUTS);
+
+	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+	       cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	ushort sreg;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	sreg = immap->im_ioport.iop_pcdat;
+	if ((pipr & mask) == mask) {
+		sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |	/* VAVPP => Hi-Z */
+				TPS2211_VCCD1);			/* 5V on	*/
+		sreg &= ~(TPS2211_VCCD0);			/* 3V off	*/
+		puts (" 5.0V card found: ");
+	} else {
+		sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |	/* VAVPP => Hi-Z */
+				TPS2211_VCCD0);			/* 3V on	*/
+		sreg &= ~(TPS2211_VCCD1);			/* 5V off	*/
+		puts (" 3.3V card found: ");
+	}
+
+	debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
+	       sreg,
+	       ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
+	       (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) ? "on" : "off"
+	      );
+
+	immap->im_ioport.iop_pcdat = sreg;
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if ((cp->cp_pbdat & TPS2211_OC) == 0) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	/* ALl voltages off / Hi-Z */
+	immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
+			TPS2211_VCCD0 | TPS2211_VCCD1 );
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	ushort sreg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	sreg  = immap->im_ioport.iop_pcdat;
+	sreg |= TPS2211_VPPD0 | TPS2211_VPPD1;		/* VAVPP always Hi-Z */
+
+	switch(vcc) {
+		case  0: 			break;	/* Switch off		*/
+		case 33: sreg |=  TPS2211_VCCD0;	/* Switch on 3.3V	*/
+		sreg &= ~TPS2211_VCCD1;
+		break;
+		case 50: sreg &= ~TPS2211_VCCD0;	/* Switch on 5.0V	*/
+		sreg |=  TPS2211_VCCD1;
+		break;
+		default: 			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	immap->im_ioport.iop_pcdat = sreg;
+
+#ifdef DEBUG
+{
+	char *s;
+
+	if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
+		s = "at 3.3V";
+	} else if (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) {
+		s = "at 5.0V";
+	} else {
+		s = "down";
+	}
+	printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */

board/cpc45/pd67290.c

@@ -1,4 +1,6 @@
-/* pd67290.c - system configuration module for SPD67290
+/*
+ * (C) Copyright 2003-2005
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
  * project.
@@ -18,51 +20,799 @@
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  * MA 02111-1307 USA
  *
- * (C) 2004 DENX Software Engineering, Heiko Schocher <hs@denx.de>
+ ********************************************************************
+ *
+ * Lots of code copied from:
+ *
+ * i82365.c 1.352 - Linux driver for Intel 82365 and compatible
+ * PC Card controllers, and Yenta-compatible PCI-to-CardBus controllers.
+ * (C) 1999 David A. Hinds <dahinds@users.sourceforge.net>
  */
 
 #include <common.h>
-#include <malloc.h>
-#include <net.h>
-#include <asm/io.h>
-#include <pci.h>
 
-/* imports */
+#ifdef CONFIG_I82365
-#include <mpc824x.h>
+
+#include <command.h>
+#include <pci.h>
+#include <pcmcia.h>
+#include <asm/io.h>
+
+#include <pcmcia/ss.h>
+#include <pcmcia/i82365.h>
+#include <pcmcia/yenta.h>
+#include <pcmcia/cirrus.h>
 
 static struct pci_device_id supported[] = {
 	{PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6729},
-	{}
+	{0, 0}
 };
 
-/***************************************************************************
+#define CYCLE_TIME	120
-*
-* SPD67290Init -
-*
-* RETURNS: -1 on error, 0 if OK
-*/
 
-int SPD67290Init (void)
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev);
+#endif
+
+typedef struct socket_info_t {
+	pci_dev_t	dev;
+	u_short		bcr;
+	u_char		pci_lat, cb_lat, sub_bus, cache;
+	u_int		cb_phys;
+
+	socket_cap_t	cap;
+	u_short		type;
+	u_int		flags;
+	cirrus_state_t	c_state;
+} socket_info_t;
+
+/* These definitions must match the pcic table! */
+typedef enum pcic_id {
+	IS_PD6710, IS_PD672X, IS_VT83C469
+} pcic_id;
+
+typedef struct pcic_t {
+	char *name;
+} pcic_t;
+
+static pcic_t pcic[] = {
+	{" Cirrus PD6710: "},
+	{" Cirrus PD672x: "},
+	{" VIA VT83C469: "},
+};
+
+static socket_info_t socket;
+static socket_state_t state;
+static struct pccard_mem_map mem;
+static struct pccard_io_map io;
+
+/*====================================================================*/
+
+/* Some PCI shortcuts */
+
+static int pci_readb (socket_info_t * s, int r, u_char * v)
 {
-	pci_dev_t devno;
+	return pci_read_config_byte (s->dev, r, v);
-	int idx = 0;		/* general index */
+}
-	ulong membaseCsr;	/* base address of device memory space */
+static int pci_writeb (socket_info_t * s, int r, u_char v)
+{
+	return pci_write_config_byte (s->dev, r, v);
+}
+static int pci_readw (socket_info_t * s, int r, u_short * v)
+{
+	return pci_read_config_word (s->dev, r, v);
+}
+static int pci_writew (socket_info_t * s, int r, u_short v)
+{
+	return pci_write_config_word (s->dev, r, v);
+}
 
-	/* find PD67290 device */
+/*====================================================================*/
-	if ((devno = pci_find_devices (supported, idx++)) < 0) {
+
-		printf ("No PD67290 device found !!\n");
+#define cb_readb(s)		readb((s)->cb_phys + 1)
+#define cb_writeb(s, v)		writeb(v, (s)->cb_phys)
+#define cb_writeb2(s, v)	writeb(v, (s)->cb_phys + 1)
+#define cb_readl(s, r)		readl((s)->cb_phys + (r))
+#define cb_writel(s, r, v)	writel(v, (s)->cb_phys + (r))
+
+
+static u_char i365_get (socket_info_t * s, u_short reg)
+{
+	u_char val;
+#ifdef CONFIG_PCMCIA_SLOT_A
+	int slot = 0;
+#else
+	int slot = 1;
+#endif
+
+	val = I365_REG (slot, reg);
+
+	cb_writeb (s, val);
+	val = cb_readb (s);
+
+	debug ("i365_get slot:%x reg: %x val: %x\n", slot, reg, val);
+	return val;
+}
+
+static void i365_set (socket_info_t * s, u_short reg, u_char data)
+{
+#ifdef CONFIG_PCMCIA_SLOT_A
+	int slot = 0;
+#else
+	int slot = 1;
+#endif
+	u_char val;
+
+	val = I365_REG (slot, reg);
+
+	cb_writeb (s, val);
+	cb_writeb2 (s, data);
+
+	debug ("i365_set slot:%x reg: %x data:%x\n", slot, reg, data);
+}
+
+static void i365_bset (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) | mask);
+}
+
+static void i365_bclr (socket_info_t * s, u_short reg, u_char mask)
+{
+	i365_set (s, reg, i365_get (s, reg) & ~mask);
+}
+
+#if 0	/* not used */
+static void i365_bflip (socket_info_t * s, u_short reg, u_char mask, int b)
+{
+	u_char d = i365_get (s, reg);
+
+	i365_set (s, reg, (b) ? (d | mask) : (d & ~mask));
+}
+
+static u_short i365_get_pair (socket_info_t * s, u_short reg)
+{
+	return (i365_get (s, reg) + (i365_get (s, reg + 1) << 8));
+}
+#endif	/* not used */
+
+static void i365_set_pair (socket_info_t * s, u_short reg, u_short data)
+{
+	i365_set (s, reg, data & 0xff);
+	i365_set (s, reg + 1, data >> 8);
+}
+
+/*======================================================================
+
+    Code to save and restore global state information for Cirrus
+    PD67xx controllers, and to set and report global configuration
+    options.
+
+======================================================================*/
+
+#define flip(v,b,f) (v = ((f)<0) ? v : ((f) ? ((v)|(b)) : ((v)&(~b))))
+
+static void cirrus_get_state (socket_info_t * s)
+{
+	int i;
+	cirrus_state_t *p = &s->c_state;
+
+	p->misc1 = i365_get (s, PD67_MISC_CTL_1);
+	p->misc1 &= (PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
+	p->misc2 = i365_get (s, PD67_MISC_CTL_2);
+	for (i = 0; i < 6; i++)
+		p->timer[i] = i365_get (s, PD67_TIME_SETUP (0) + i);
+
+}
+
+static void cirrus_set_state (socket_info_t * s)
+{
+	int i;
+	u_char misc;
+	cirrus_state_t *p = &s->c_state;
+
+	misc = i365_get (s, PD67_MISC_CTL_2);
+	i365_set (s, PD67_MISC_CTL_2, p->misc2);
+	if (misc & PD67_MC2_SUSPEND)
+		udelay (50000);
+	misc = i365_get (s, PD67_MISC_CTL_1);
+	misc &= ~(PD67_MC1_MEDIA_ENA | PD67_MC1_INPACK_ENA);
+	i365_set (s, PD67_MISC_CTL_1, misc | p->misc1);
+	for (i = 0; i < 6; i++)
+		i365_set (s, PD67_TIME_SETUP (0) + i, p->timer[i]);
+}
+
+static u_int cirrus_set_opts (socket_info_t * s)
+{
+	cirrus_state_t *p = &s->c_state;
+	u_int mask = 0xffff;
+#if DEBUG
+	char buf[200];
+
+	memset (buf, 0, 200);
+#endif
+
+	if (has_ring == -1)
+		has_ring = 1;
+	flip (p->misc2, PD67_MC2_IRQ15_RI, has_ring);
+	flip (p->misc2, PD67_MC2_DYNAMIC_MODE, dynamic_mode);
+#if DEBUG
+	if (p->misc2 & PD67_MC2_IRQ15_RI)
+		strcat (buf, " [ring]");
+	if (p->misc2 & PD67_MC2_DYNAMIC_MODE)
+		strcat (buf, " [dyn mode]");
+	if (p->misc1 & PD67_MC1_INPACK_ENA)
+		strcat (buf, " [inpack]");
+#endif
+
+	if (p->misc2 & PD67_MC2_IRQ15_RI)
+		mask &= ~0x8000;
+	if (has_led > 0) {
+#if DEBUG
+		strcat (buf, " [led]");
+#endif
+		mask &= ~0x1000;
+	}
+	if (has_dma > 0) {
+#if DEBUG
+		strcat (buf, " [dma]");
+#endif
+		mask &= ~0x0600;
+		flip (p->misc2, PD67_MC2_FREQ_BYPASS, freq_bypass);
+#if DEBUG
+		if (p->misc2 & PD67_MC2_FREQ_BYPASS)
+			strcat (buf, " [freq bypass]");
+#endif
+	}
+
+	if (setup_time >= 0)
+		p->timer[0] = p->timer[3] = setup_time;
+	if (cmd_time > 0) {
+		p->timer[1] = cmd_time;
+		p->timer[4] = cmd_time * 2 + 4;
+	}
+	if (p->timer[1] == 0) {
+		p->timer[1] = 6;
+		p->timer[4] = 16;
+		if (p->timer[0] == 0)
+			p->timer[0] = p->timer[3] = 1;
+	}
+	if (recov_time >= 0)
+		p->timer[2] = p->timer[5] = recov_time;
+
+	debug ("i82365 Opt: %s [%d/%d/%d] [%d/%d/%d]\n",
+		buf,
+		p->timer[0], p->timer[1], p->timer[2],
+		p->timer[3], p->timer[4], p->timer[5]);
+
+	return mask;
+}
+
+/*======================================================================
+
+    Routines to handle common CardBus options
+
+======================================================================*/
+
+/* Default settings for PCI command configuration register */
+#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
+		  PCI_COMMAND_MASTER|PCI_COMMAND_WAIT)
+
+static void cb_get_state (socket_info_t * s)
+{
+	pci_readb (s, PCI_CACHE_LINE_SIZE, &s->cache);
+	pci_readb (s, PCI_LATENCY_TIMER, &s->pci_lat);
+	pci_readb (s, CB_LATENCY_TIMER, &s->cb_lat);
+	pci_readb (s, CB_CARDBUS_BUS, &s->cap.cardbus);
+	pci_readb (s, CB_SUBORD_BUS, &s->sub_bus);
+	pci_readw (s, CB_BRIDGE_CONTROL, &s->bcr);
+}
+
+static void cb_set_state (socket_info_t * s)
+{
+	pci_writew (s, PCI_COMMAND, CMD_DFLT);
+	pci_writeb (s, PCI_CACHE_LINE_SIZE, s->cache);
+	pci_writeb (s, PCI_LATENCY_TIMER, s->pci_lat);
+	pci_writeb (s, CB_LATENCY_TIMER, s->cb_lat);
+	pci_writeb (s, CB_CARDBUS_BUS, s->cap.cardbus);
+	pci_writeb (s, CB_SUBORD_BUS, s->sub_bus);
+	pci_writew (s, CB_BRIDGE_CONTROL, s->bcr);
+}
+
+static void cb_set_opts (socket_info_t * s)
+{
+}
+
+/*======================================================================
+
+    Power control for Cardbus controllers: used both for 16-bit and
+    Cardbus cards.
+
+======================================================================*/
+
+static int cb_set_power (socket_info_t * s, socket_state_t * state)
+{
+	u_int reg = 0;
+
+	reg = I365_PWR_NORESET;
+	if (state->flags & SS_PWR_AUTO)
+		reg |= I365_PWR_AUTO;
+	if (state->flags & SS_OUTPUT_ENA)
+		reg |= I365_PWR_OUT;
+	if (state->Vpp != 0) {
+		if (state->Vpp == 120) {
+			reg |= I365_VPP1_12V;
+			puts (" 12V card found: ");
+		} else if (state->Vpp == state->Vcc) {
+			reg |= I365_VPP1_5V;
+		} else {
+			puts (" power not found: ");
+			return -1;
+		}
+	}
+	if (state->Vcc != 0) {
+		reg |= I365_VCC_5V;
+		if (state->Vcc == 33) {
+			puts (" 3.3V card found: ");
+			i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		} else if (state->Vcc == 50) {
+			puts (" 5V card found: ");
+			i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		} else {
+			puts (" power not found: ");
+			return -1;
+		}
+	}
+
+	if (reg != i365_get (s, I365_POWER)) {
+		reg = (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V);
+		i365_set (s, I365_POWER, reg);
+	}
+
+	return 0;
+}
+
+/*======================================================================
+
+    Generic routines to get and set controller options
+
+======================================================================*/
+
+static void get_bridge_state (socket_info_t * s)
+{
+	cirrus_get_state (s);
+	cb_get_state (s);
+}
+
+static void set_bridge_state (socket_info_t * s)
+{
+	cb_set_state (s);
+	i365_set (s, I365_GBLCTL, 0x00);
+	i365_set (s, I365_GENCTL, 0x00);
+	cirrus_set_state (s);
+}
+
+static void set_bridge_opts (socket_info_t * s)
+{
+	cirrus_set_opts (s);
+	cb_set_opts (s);
+}
+
+/*====================================================================*/
+#define PD67_EXT_INDEX		0x2e	/* Extension index */
+#define PD67_EXT_DATA		0x2f	/* Extension data */
+#define PD67_EXD_VS1(s)		(0x01 << ((s)<<1))
+
+#define pd67_ext_get(s, r) \
+    (i365_set(s, PD67_EXT_INDEX, r), i365_get(s, PD67_EXT_DATA))
+
+static int i365_get_status (socket_info_t * s, u_int * value)
+{
+	u_int status;
+	u_char val;
+	u_char power, vcc, vpp;
+	u_int powerstate;
+
+	status = i365_get (s, I365_IDENT);
+	status = i365_get (s, I365_STATUS);
+	*value = ((status & I365_CS_DETECT) == I365_CS_DETECT) ? SS_DETECT : 0;
+	if (i365_get (s, I365_INTCTL) & I365_PC_IOCARD) {
+		*value |= (status & I365_CS_STSCHG) ? 0 : SS_STSCHG;
+	} else {
+		*value |= (status & I365_CS_BVD1) ? 0 : SS_BATDEAD;
+		*value |= (status & I365_CS_BVD2) ? 0 : SS_BATWARN;
+	}
+	*value |= (status & I365_CS_WRPROT) ? SS_WRPROT : 0;
+	*value |= (status & I365_CS_READY) ? SS_READY : 0;
+	*value |= (status & I365_CS_POWERON) ? SS_POWERON : 0;
+
+	/* Check for Cirrus CL-PD67xx chips */
+	i365_set (s, PD67_CHIP_INFO, 0);
+	val = i365_get (s, PD67_CHIP_INFO);
+	s->type = -1;
+	if ((val & PD67_INFO_CHIP_ID) == PD67_INFO_CHIP_ID) {
+		val = i365_get (s, PD67_CHIP_INFO);
+		if ((val & PD67_INFO_CHIP_ID) == 0) {
+			s->type = (val & PD67_INFO_SLOTS) ? IS_PD672X : IS_PD6710;
+			i365_set (s, PD67_EXT_INDEX, 0xe5);
+			if (i365_get (s, PD67_EXT_INDEX) != 0xe5)
+				s->type = IS_VT83C469;
+		}
+	} else {
+		printf ("no Cirrus Chip found\n");
+		*value = 0;
 		return -1;
 	}
-	/* - 0xfe000000 see MPC 8245 Users Manual Adress Map B */
+
-	membaseCsr = PCMCIA_IO_BASE - 0xfe000000;
+	power = i365_get (s, I365_POWER);
+	state.flags |= (power & I365_PWR_AUTO) ? SS_PWR_AUTO : 0;
+	state.flags |= (power & I365_PWR_OUT) ? SS_OUTPUT_ENA : 0;
+	vcc = power & I365_VCC_MASK;
+	vpp = power & I365_VPP1_MASK;
+	state.Vcc = state.Vpp = 0;
+	if((vcc== 0) || (vpp == 0)) {
+		/*
+		 * On the Cirrus we get the info which card voltage
+		 * we have in EXTERN DATA and write it to MISC_CTL1
+		 */
+		powerstate = pd67_ext_get(s, PD67_EXTERN_DATA);
+		if (powerstate & PD67_EXD_VS1(0)) {
+			/* 5V Card */
+			i365_bclr (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		} else {
+			/* 3.3V Card */
+			i365_bset (s, PD67_MISC_CTL_1, PD67_MC1_VCC_3V);
+		}
+		i365_set (s, I365_POWER, (I365_PWR_OUT | I365_PWR_NORESET | I365_VCC_5V | I365_VPP1_5V));
+		power = i365_get (s, I365_POWER);
+	}
+	if (power & I365_VCC_5V) {
+		state.Vcc = (i365_get(s, PD67_MISC_CTL_1) & PD67_MC1_VCC_3V) ? 33 : 50;
+	}
+
+	if (power == I365_VPP1_12V)
+		state.Vpp = 120;
+
+	/* IO card, RESET flags, IO interrupt */
+	power = i365_get (s, I365_INTCTL);
+	state.flags |= (power & I365_PC_RESET) ? 0 : SS_RESET;
+	if (power & I365_PC_IOCARD)
+		state.flags |= SS_IOCARD;
+	state.io_irq = power & I365_IRQ_MASK;
+
+	/* Card status change mask */
+	power = i365_get (s, I365_CSCINT);
+	state.csc_mask = (power & I365_CSC_DETECT) ? SS_DETECT : 0;
+	if (state.flags & SS_IOCARD)
+		state.csc_mask |= (power & I365_CSC_STSCHG) ? SS_STSCHG : 0;
+	else {
+		state.csc_mask |= (power & I365_CSC_BVD1) ? SS_BATDEAD : 0;
+		state.csc_mask |= (power & I365_CSC_BVD2) ? SS_BATWARN : 0;
+		state.csc_mask |= (power & I365_CSC_READY) ? SS_READY : 0;
+	}
+	debug ("i82365: GetStatus(0) = flags %#3.3x, Vcc %d, Vpp %d, "
+		"io_irq %d, csc_mask %#2.2x\n", state.flags,
+		state.Vcc, state.Vpp, state.io_irq, state.csc_mask);
+
+	return 0;
+}	/* i365_get_status */
+
+static int i365_set_socket (socket_info_t * s, socket_state_t * state)
+{
+	u_char reg;
+
+	set_bridge_state (s);
+
+	/* IO card, RESET flag */
+	reg = 0;
+	reg |= (state->flags & SS_RESET) ? 0 : I365_PC_RESET;
+	reg |= (state->flags & SS_IOCARD) ? I365_PC_IOCARD : 0;
+	i365_set (s, I365_INTCTL, reg);
+
+	cb_set_power (s, state);
+
+#if 0
+	/* Card status change interrupt mask */
+	reg = s->cs_irq << 4;
+	if (state->csc_mask & SS_DETECT)
+		reg |= I365_CSC_DETECT;
+	if (state->flags & SS_IOCARD) {
+		if (state->csc_mask & SS_STSCHG)
+			reg |= I365_CSC_STSCHG;
+	} else {
+		if (state->csc_mask & SS_BATDEAD)
+			reg |= I365_CSC_BVD1;
+		if (state->csc_mask & SS_BATWARN)
+			reg |= I365_CSC_BVD2;
+		if (state->csc_mask & SS_READY)
+			reg |= I365_CSC_READY;
+	}
+	i365_set (s, I365_CSCINT, reg);
+	i365_get (s, I365_CSC);
+#endif	/* 0 */
+
+	return 0;
+}	/* i365_set_socket */
+
+/*====================================================================*/
+
+static int i365_set_mem_map (socket_info_t * s, struct pccard_mem_map *mem)
+{
+	u_short base, i;
+	u_char map;
+
+	debug ("i82365: SetMemMap(%d, %#2.2x, %d ns, %#5.5lx-%#5.5lx, %#5.5x)\n",
+		mem->map, mem->flags, mem->speed,
+		mem->sys_start, mem->sys_stop, mem->card_start);
+
+	map = mem->map;
+	if ((map > 4) ||
+	    (mem->card_start > 0x3ffffff) ||
+	    (mem->sys_start > mem->sys_stop) ||
+	    (mem->speed > 1000)) {
+		return -1;
+	}
+
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_MEM (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_MEM (map));
+
+	/* Take care of high byte, for PCI controllers */
+	i365_set (s, CB_MEM_PAGE (map), mem->sys_start >> 24);
+
+	base = I365_MEM (map);
+	i = (mem->sys_start >> 12) & 0x0fff;
+	if (mem->flags & MAP_16BIT)
+		i |= I365_MEM_16BIT;
+	if (mem->flags & MAP_0WS)
+		i |= I365_MEM_0WS;
+	i365_set_pair (s, base + I365_W_START, i);
+
+	i = (mem->sys_stop >> 12) & 0x0fff;
+	switch (mem->speed / CYCLE_TIME) {
+	case 0:
+		break;
+	case 1:
+		i |= I365_MEM_WS0;
+		break;
+	case 2:
+		i |= I365_MEM_WS1;
+		break;
+	default:
+		i |= I365_MEM_WS1 | I365_MEM_WS0;
+		break;
+	}
+	i365_set_pair (s, base + I365_W_STOP, i);
+
+	i = 0;
+	if (mem->flags & MAP_WRPROT)
+		i |= I365_MEM_WRPROT;
+	if (mem->flags & MAP_ATTRIB)
+		i |= I365_MEM_REG;
+	i365_set_pair (s, base + I365_W_OFF, i);
+
+	/* set System Memory map Upper Adress */
+	i365_set(s, PD67_EXT_INDEX, PD67_MEM_PAGE(map));
+	i365_set(s, PD67_EXT_DATA, ((mem->sys_start >> 24) & 0xff));
+
+	/* Turn on the window if necessary */
+	if (mem->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_MEM (map));
+	return 0;
+}	/* i365_set_mem_map */
+
+static int i365_set_io_map (socket_info_t * s, struct pccard_io_map *io)
+{
+	u_char map, ioctl;
+
+	map = io->map;
+	/* comment out: comparison is always false due to limited range of data type */
+	if ((map > 1) || /* (io->start > 0xffff) || (io->stop > 0xffff) || */
+	    (io->stop < io->start))
+		return -1;
+	/* Turn off the window before changing anything */
+	if (i365_get (s, I365_ADDRWIN) & I365_ENA_IO (map))
+		i365_bclr (s, I365_ADDRWIN, I365_ENA_IO (map));
+	i365_set_pair (s, I365_IO (map) + I365_W_START, io->start);
+	i365_set_pair (s, I365_IO (map) + I365_W_STOP, io->stop);
+	ioctl = i365_get (s, I365_IOCTL) & ~I365_IOCTL_MASK (map);
+	if (io->speed)
+		ioctl |= I365_IOCTL_WAIT (map);
+	if (io->flags & MAP_0WS)
+		ioctl |= I365_IOCTL_0WS (map);
+	if (io->flags & MAP_16BIT)
+		ioctl |= I365_IOCTL_16BIT (map);
+	if (io->flags & MAP_AUTOSZ)
+		ioctl |= I365_IOCTL_IOCS16 (map);
+	i365_set (s, I365_IOCTL, ioctl);
+	/* Turn on the window if necessary */
+	if (io->flags & MAP_ACTIVE)
+		i365_bset (s, I365_ADDRWIN, I365_ENA_IO (map));
+	return 0;
+}	/* i365_set_io_map */
+
+/*====================================================================*/
+
+/*
+ * PCI_ADDR = (HOST_ADDR - 0xfe000000)
+ * see MPC 8245 Users Manual Adress Map B
+ */
+#define	HOST_TO_PCI(addr)	((addr) - 0xfe000000)
+#define	PCI_TO_HOST(addr)	((addr) + 0xfe000000)
+
+int i82365_init (void)
+{
+	u_int val;
+	int i;
+
+	if ((socket.dev = pci_find_devices (supported, 0)) < 0) {
+		/* Controller not found */
+		printf ("No PD67290 device found !!\n");
+		return 1;
+	}
+	debug ("i82365 Device Found!\n");
+
+	socket.cb_phys = PCMCIA_IO_BASE;
 
 	/* set base address */
-	pci_write_config_dword (devno, PCI_BASE_ADDRESS_0, membaseCsr);
+	pci_write_config_dword (socket.dev, PCI_BASE_ADDRESS_0,
+		HOST_TO_PCI(socket.cb_phys));
 
 	/* enable mapped memory and IO addresses */
-	pci_write_config_dword (devno,
+	pci_write_config_dword (socket.dev,
 				PCI_COMMAND,
 				PCI_COMMAND_MEMORY |
 				PCI_COMMAND_IO | PCI_COMMAND_WAIT);
+
+	get_bridge_state (&socket);
+	set_bridge_opts (&socket);
+
+	i = i365_get_status (&socket, &val);
+
+	if (i > -1) {
+		puts (pcic[socket.type].name);
+	} else {
+		printf ("i82365: Controller not found.\n");
+		return 1;
+	}
+	if((val & SS_DETECT) != SS_DETECT){
+		puts ("No card\n");
+		return 1;
+	}
+
+	state.flags |= SS_OUTPUT_ENA;
+
+	i365_set_socket (&socket, &state);
+
+	for (i = 500; i; i--) {
+		if ((i365_get (&socket, I365_STATUS) & I365_CS_READY))
+			break;
+		udelay (1000);
+	}
+
+	if (i == 0) {
+		/* PC Card not ready for data transfer */
+		puts ("i82365 PC Card not ready for data transfer\n");
+		return 1;
+	}
+	debug (" PC Card ready for data transfer: ");
+
+	mem.map = 0;
+	mem.flags = MAP_ATTRIB | MAP_ACTIVE;
+	mem.speed = 300;
+	mem.sys_start = CFG_PCMCIA_MEM_ADDR;
+	mem.sys_stop = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE - 1;
+	mem.card_start = 0;
+	i365_set_mem_map (&socket, &mem);
+
+	mem.map = 1;
+	mem.flags = MAP_ACTIVE;
+	mem.speed = 300;
+	mem.sys_start = CFG_PCMCIA_MEM_ADDR + CFG_PCMCIA_MEM_SIZE;
+	mem.sys_stop = CFG_PCMCIA_MEM_ADDR + (2 * CFG_PCMCIA_MEM_SIZE) - 1;
+	mem.card_start = 0;
+	i365_set_mem_map (&socket, &mem);
+
+#ifdef DEBUG
+	i82365_dump_regions (socket.dev);
+#endif
+
 	return 0;
 }
+
+void i82365_exit (void)
+{
+	io.map = 0;
+	io.flags = 0;
+	io.speed = 0;
+	io.start = 0;
+	io.stop = 0x1;
+
+	i365_set_io_map (&socket, &io);
+
+	mem.map = 0;
+	mem.flags = 0;
+	mem.speed = 0;
+	mem.sys_start = 0;
+	mem.sys_stop = 0x1000;
+	mem.card_start = 0;
+
+	i365_set_mem_map (&socket, &mem);
+
+	mem.map = 1;
+	mem.flags = 0;
+	mem.speed = 0;
+	mem.sys_start = 0;
+	mem.sys_stop = 0x1000;
+	mem.card_start = 0;
+
+	i365_set_mem_map (&socket, &mem);
+
+	state.Vcc = state.Vpp = 0;
+
+	i365_set_socket (&socket, &state);
+}
+
+int pcmcia_on (void)
+{
+	u_int rc;
+
+	debug ("Enable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	rc = i82365_init();
+	if (rc)
+		goto exit;
+
+	rc = check_ide_device(0);
+	if (rc == 0)
+		goto exit;
+
+	i82365_exit();
+
+exit:
+	return rc;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_off (void)
+{
+	printf ("Disable PCMCIA " PCMCIA_SLOT_MSG "\n");
+
+	i82365_exit();
+
+	return 0;
+}
+#endif
+
+/*======================================================================
+
+    Debug stuff
+
+======================================================================*/
+
+#ifdef DEBUG
+static void i82365_dump_regions (pci_dev_t dev)
+{
+	u_int tmp[2];
+	u_int *mem = (void *) socket.cb_phys;
+	u_char *cis = (void *) CFG_PCMCIA_MEM_ADDR;
+	u_char *ide = (void *) (CFG_ATA_BASE_ADDR + CFG_ATA_REG_OFFSET);
+
+	pci_read_config_dword (dev, 0x00, tmp + 0);
+	pci_read_config_dword (dev, 0x80, tmp + 1);
+
+	printf ("PCI CONF: %08X ... %08X\n",
+		tmp[0], tmp[1]);
+	printf ("PCI MEM:  ... %08X ... %08X\n",
+		mem[0x8 / 4], mem[0x800 / 4]);
+	printf ("CIS:      ...%c%c%c%c%c%c%c%c...\n",
+		cis[0x38], cis[0x3a], cis[0x3c], cis[0x3e],
+		cis[0x40], cis[0x42], cis[0x44], cis[0x48]);
+	printf ("CIS CONF: %02X %02X %02X ...\n",
+		cis[0x200], cis[0x202], cis[0x204]);
+	printf ("IDE:      %02X %02X %02X %02X %02X %02X %02X %02X\n",
+		ide[0], ide[1], ide[2], ide[3],
+		ide[4], ide[5], ide[6], ide[7]);
+}
+#endif	/* DEBUG */
+
+#endif /* CONFIG_I82365 */

board/cpu87/cpu87.c

@@ -197,7 +197,7 @@ const iop_conf_t iop_conf_tab[4][32] = {
  */
 int checkboard (void)
 {
-	printf ("Board: CPU87 (Rev %02x)\n", CPU86_REV);
+	printf ("Board: CPU87 (Rev %02x)\n", CPU86_REV & 0x7f);
 	return 0;
 }
 
@@ -280,7 +280,7 @@ long int initdram (int board_type)
 	volatile memctl8260_t *memctl = &immap->im_memctl;
 
 #ifndef CFG_RAMBOOT
-	ulong size8, size9;
+	ulong size8, size9, size10;
 #endif
 	long psize;
 
@@ -294,17 +294,25 @@ long int initdram (int board_type)
 	 */
 	size8 = try_init (memctl, CFG_PSDMR_8COL, CFG_OR2_8COL,
 			  (uchar *) CFG_SDRAM_BASE);
+	
 	size9 = try_init (memctl, CFG_PSDMR_9COL, CFG_OR2_9COL,
 			  (uchar *) CFG_SDRAM_BASE);
 	
-	if (size8 < size9) {
+	size10 = try_init (memctl, CFG_PSDMR_10COL, CFG_OR2_10COL,
-		psize = size9;
+			  (uchar *) CFG_SDRAM_BASE);
-		printf ("(60x:9COL) ");
+	
-	} else {
+	psize = max(size8,max(size9,size10));
+	
+	if (psize == size8) {
 		psize = try_init (memctl, CFG_PSDMR_8COL, CFG_OR2_8COL,
 				  (uchar *) CFG_SDRAM_BASE);
 		printf ("(60x:8COL) ");
-	}
+	} else if (psize == size9){
+		psize = try_init (memctl, CFG_PSDMR_9COL, CFG_OR2_9COL,
+				  (uchar *) CFG_SDRAM_BASE);
+		printf ("(60x:9COL) ");
+	} else
+		printf ("(60x:10COL) ");
 
 #endif	/* CFG_RAMBOOT */
 

board/etin/kvme080/Makefile

@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS =  $(BOARD).o multiverse.o
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/etin/kvme080/config.mk

@@ -0,0 +1,30 @@
+#
+# (C) Copyright 2005
+# Sangmoon, Etin Systems, dogoil@etinsys.com.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# KVME080 board
+#
+
+TEXT_BASE = 0xFFF00000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE)

board/etin/kvme080/kvme080.c

@@ -0,0 +1,193 @@
+/*
+ * (C) Copyright 2005
+ * Sangmoon Kim, Etin Systems. dogoil@etinsys.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc824x.h>
+#include <pci.h>
+#include <i2c.h>
+#include <asm/processor.h>
+
+int checkboard(void)
+{
+	puts ("Board: KVME080\n");
+	return 0;
+}
+
+unsigned long setdram(int m, int row, int col, int bank)
+{
+	int i;
+	unsigned long start, end;
+	uint32_t mccr1;
+	uint32_t mear1 = 0, emear1 = 0, msar1 = 0, emsar1 = 0;
+	uint32_t mear2 = 0, emear2 = 0, msar2 = 0, emsar2 = 0;
+	uint8_t mber = 0;
+
+	CONFIG_READ_WORD(MCCR1, mccr1);
+	mccr1 &= 0xffff0000;
+
+	start = CFG_SDRAM_BASE;
+	end = start + (1 << (col + row + 3) ) * bank - 1;
+
+	for (i = 0; i < m; i++) {
+		mccr1 |= ((row == 13)? 2 : (bank == 4)? 0 : 3) << i * 2;
+		if (i < 4) {
+			msar1  |= ((start >> 20) & 0xff) << i * 8;
+			emsar1 |= ((start >> 28) & 0xff) << i * 8;
+			mear1  |= ((end >> 20) & 0xff) << i * 8;
+			emear1 |= ((end >> 28) & 0xff) << i * 8;
+		} else {
+			msar2  |= ((start >> 20) & 0xff) << (i-4) * 8;
+			emsar2 |= ((start >> 28) & 0xff) << (i-4) * 8;
+			mear2  |= ((end >> 20) & 0xff) << (i-4) * 8;
+			emear2 |= ((end >> 28) & 0xff) << (i-4) * 8;
+		}
+		mber |= 1 << i;
+		start += (1 << (col + row + 3) ) * bank;
+		end += (1 << (col + row + 3) ) * bank;
+	}
+	for (; i < 8; i++) {
+		if (i < 4) {
+			msar1  |= 0xff << i * 8;
+			emsar1 |= 0x30 << i * 8;
+			mear1  |= 0xff << i * 8;
+			emear1 |= 0x30 << i * 8;
+		} else {
+			msar2  |= 0xff << (i-4) * 8;
+			emsar2 |= 0x30 << (i-4) * 8;
+			mear2  |= 0xff << (i-4) * 8;
+			emear2 |= 0x30 << (i-4) * 8;
+		}
+	}
+
+	CONFIG_WRITE_WORD(MCCR1, mccr1);
+	CONFIG_WRITE_WORD(MSAR1, msar1);
+	CONFIG_WRITE_WORD(EMSAR1, emsar1);
+	CONFIG_WRITE_WORD(MEAR1, mear1);
+	CONFIG_WRITE_WORD(EMEAR1, emear1);
+	CONFIG_WRITE_WORD(MSAR2, msar2);
+	CONFIG_WRITE_WORD(EMSAR2, emsar2);
+	CONFIG_WRITE_WORD(MEAR2, mear2);
+	CONFIG_WRITE_WORD(EMEAR2, emear2);
+	CONFIG_WRITE_BYTE(MBER, mber);
+
+	return (1 << (col + row + 3) ) * bank * m;
+}
+
+long int initdram(int board_type)
+{
+	unsigned int msr;
+	long int size = 0;
+
+	msr = mfmsr();
+	mtmsr(msr & ~(MSR_IR | MSR_DR));
+	mtspr(IBAT2L, CFG_IBAT0L + 0x10000000);
+	mtspr(IBAT2U, CFG_IBAT0U + 0x10000000);
+	mtspr(DBAT2L, CFG_DBAT0L + 0x10000000);
+	mtspr(DBAT2U, CFG_DBAT0U + 0x10000000);
+	mtmsr(msr);
+
+	if (setdram(2,13,10,4) == get_ram_size(CFG_SDRAM_BASE, 0x20000000))
+		size = 0x20000000;	/* 512MB */
+	else if (setdram(1,13,10,4) == get_ram_size(CFG_SDRAM_BASE, 0x10000000))
+		size = 0x10000000;	/* 256MB */
+	else if (setdram(2,13,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x10000000))
+		size = 0x10000000;	/* 256MB */
+	else if (setdram(1,13,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x08000000))
+		size = 0x08000000;	/* 128MB */
+	else if (setdram(2,12,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x08000000))
+		size = 0x08000000;	/* 128MB */
+	else if (setdram(1,12,9,4) == get_ram_size(CFG_SDRAM_BASE, 0x04000000))
+		size = 0x04000000;	/* 64MB */
+
+	msr = mfmsr();
+	mtmsr(msr & ~(MSR_IR | MSR_DR));
+	mtspr(IBAT2L, CFG_IBAT2L);
+	mtspr(IBAT2U, CFG_IBAT2U);
+	mtspr(DBAT2L, CFG_DBAT2L);
+	mtspr(DBAT2U, CFG_DBAT2U);
+	mtmsr(msr);
+
+	return size;
+}
+
+struct pci_controller hose;
+
+void pci_init_board(void)
+{
+	pci_mpc824x_init(&hose);
+}
+
+int board_early_init_f(void)
+{
+	*(volatile unsigned char *)(0xff080120) = 0xfb;
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	unsigned int msr;
+
+	CONFIG_WRITE_WORD(ERCR1, 0x95ff8000);
+	CONFIG_WRITE_WORD(ERCR3, 0x0c00000e);
+	CONFIG_WRITE_WORD(ERCR4, 0x0800000e);
+
+	msr = mfmsr();
+	mtmsr(msr & ~(MSR_IR | MSR_DR));
+	mtspr(IBAT1L, 0x70000000 | BATL_PP_10 | BATL_CACHEINHIBIT);
+	mtspr(IBAT1U, 0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP);
+	mtspr(DBAT1L, 0x70000000 | BATL_PP_10 | BATL_CACHEINHIBIT);
+	mtspr(DBAT1U, 0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP);
+	mtmsr(msr);
+
+	return 0;
+}
+
+extern int multiverse_init(void);
+
+int misc_init_r(void)
+{
+	multiverse_init();
+	return 0;
+}
+
+void *nvram_read(void *dest, const long src, size_t count)
+{
+	volatile uchar *d = (volatile uchar*) dest;
+	volatile uchar *s = (volatile uchar*) src;
+	while(count--) {
+		*d++ = *s++;
+		asm volatile("sync");
+	}
+	return dest;
+}
+
+void nvram_write(long dest, const void *src, size_t count)
+{
+	volatile uchar *d = (volatile uchar*)dest;
+	volatile uchar *s = (volatile uchar*)src;
+	while(count--) {
+		*d++ = *s++;
+		asm volatile("sync");
+	}
+}

board/etin/kvme080/multiverse.c

@@ -0,0 +1,186 @@
+/*
+ * multiverse.c
+ *
+ * VME driver for Multiverse
+ *
+ * Author : Sangmoon Kim
+ *	    dogoil@etinsys.com
+ *
+ * Copyright 2005 ETIN SYSTEMS Co.,Ltd.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <pci.h>
+
+#include "multiverse.h"
+
+static unsigned long vme_asi_addr;
+static unsigned long vme_iack_addr;
+static unsigned long pci_reg_addr;
+static unsigned long vme_reg_addr;
+
+int multiv_reset(unsigned long base)
+{
+	writeb(0x09, base + VME_SLAVE32_AM);
+	writeb(0x39, base + VME_SLAVE24_AM);
+	writeb(0x29, base + VME_SLAVE16_AM);
+	writeb(0x2f, base + VME_SLAVE_REG_AM);
+	writeb((VME_A32_SLV_BUS >> 24) & 0xff, base + VME_SLAVE32_A);
+	writeb((VME_A24_SLV_BUS >> 16) & 0xff, base + VME_SLAVE24_A);
+	writeb((VME_A16_SLV_BUS >> 8 ) & 0xff, base + VME_SLAVE16_A);
+#ifdef A32_SLV_WINDOW
+	if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+		writeb(((~(VME_A32_SLV_SIZE-1)) >> 24) & 0xff,
+				base + VME_SLAVE32_MASK);
+		writeb(0x01, base + VME_SLAVE32_EN);
+	} else {
+		writeb(0xff, base + VME_SLAVE32_MASK);
+		writeb(0x00, base + VME_SLAVE32_EN);
+	}
+#else
+	writeb(0xff, base + VME_SLAVE32_MASK);
+	writeb(0x00, base + VME_SLAVE32_EN);
+#endif
+#ifdef A24_SLV_WINDOW
+	if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+		writeb(((~(VME_A24_SLV_SIZE-1)) >> 16) & 0xff,
+				base + VME_SLAVE24_MASK);
+		writeb(0x01, base + VME_SLAVE24_EN);
+	} else {
+		writeb(0xff, base + VME_SLAVE24_MASK);
+		writeb(0x00, base + VME_SLAVE24_EN);
+	}
+#else
+	writeb(0xff, base + VME_SLAVE24_MASK);
+	writeb(0x00, base + VME_SLAVE24_EN);
+#endif
+#ifdef A16_SLV_WINDOW
+	if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+		writeb(((~(VME_A16_SLV_SIZE-1)) >> 8) & 0xff,
+				base + VME_SLAVE16_MASK);
+		writeb(0x01, base + VME_SLAVE16_EN);
+	} else {
+		writeb(0xff, base + VME_SLAVE16_MASK);
+		writeb(0x00, base + VME_SLAVE16_EN);
+	}
+#else
+	writeb(0xff, base + VME_SLAVE16_MASK);
+	writeb(0x00, base + VME_SLAVE16_EN);
+#endif
+#ifdef REG_SLV_WINDOW
+	if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+		writeb(((~(VME_REG_SLV_SIZE-1)) >> 16) & 0xff,
+				base + VME_SLAVE_REG_MASK);
+		writeb(0x01, base + VME_SLAVE_REG_EN);
+	} else {
+		writeb(0xf8, base + VME_SLAVE_REG_MASK);
+	}
+#else
+	writeb(0xf8, base + VME_SLAVE_REG_MASK);
+#endif
+	writeb(0x09, base + VME_MASTER32_AM);
+	writeb(0x39, base + VME_MASTER24_AM);
+	writeb(0x29, base + VME_MASTER16_AM);
+	writeb(0x2f, base + VME_MASTER_REG_AM);
+	writel(0x00000000, base + VME_RMW_ADRS);
+	writeb(0x00, base + VME_IRQ);
+	writeb(0x00, base + VME_INT_EN);
+	writel(0x00000000, base + VME_IRQ1_REG);
+	writel(0x00000000, base + VME_IRQ2_REG);
+	writel(0x00000000, base + VME_IRQ3_REG);
+	writel(0x00000000, base + VME_IRQ4_REG);
+	writel(0x00000000, base + VME_IRQ5_REG);
+	writel(0x00000000, base + VME_IRQ6_REG);
+	writel(0x00000000, base + VME_IRQ7_REG);
+	return 0;
+}
+
+void multiv_auto_slot_id(unsigned long base)
+{
+	unsigned int vector;
+	int slot_id = 1;
+	if (readb(base + VME_CTRL) & VME_CTRL_SYSFAIL) {
+		*(volatile unsigned int*)(base + VME_IRQ2_REG) = 0xfe;
+		writeb(readb(base + VME_IRQ) | 0x04, base + VME_IRQ);
+		writeb(readb(base + VME_CTRL) & ~VME_CTRL_SYSFAIL,
+				base + VME_CTRL);
+		while (readb(base + VME_STATUS) & VME_STATUS_SYSFAIL);
+		if (readb(base + VME_STATUS) & VME_STATUS_SYSCON) {
+			while (readb(base + VME_INT) & 0x04) {
+				vector = *(volatile unsigned int*)
+					(vme_iack_addr + VME_IACK2);
+				*(unsigned char*)(vme_asi_addr + 0x7ffff)
+					= (slot_id << 3) & 0xff;
+				slot_id ++;
+				if (slot_id > 31)
+					break;
+			}
+		}
+	}
+}
+
+int multiverse_init(void)
+{
+	int i;
+	pci_dev_t pdev;
+	unsigned int bar[6];
+
+	pdev = pci_find_device(0x1895, 0x0001, 0);
+
+	if (pdev == 0)
+		return -1;
+
+	for (i = 0; i < 6; i++)
+		pci_read_config_dword (pdev,
+				PCI_BASE_ADDRESS_0 + i * 4, &bar[i]);
+
+	pci_reg_addr = bar[0];
+	vme_reg_addr = bar[1] + 0x00F00000;
+	vme_iack_addr = bar[1] + 0x00200000;
+	vme_asi_addr = bar[3];
+
+	pci_write_config_dword (pdev, PCI_COMMAND,
+		PCI_COMMAND_IO | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+	writel(0xFF000000, pci_reg_addr + P_TA1);
+	writel(0x04, pci_reg_addr + P_IMG_CTRL1);
+	writel(0xf0000000, pci_reg_addr + P_TA2);
+	writel(0x04, pci_reg_addr + P_IMG_CTRL2);
+	writel(0xF1000000, pci_reg_addr + P_TA3);
+	writel(0x04, pci_reg_addr + P_IMG_CTRL3);
+	writel(VME_A32_MSTR_BUS, pci_reg_addr + P_TA5);
+	writel(~(VME_A32_MSTR_SIZE-1), pci_reg_addr + P_AM5);
+	writel(0x04, pci_reg_addr + P_IMG_CTRL5);
+
+	writel(VME_A32_SLV_BUS, pci_reg_addr + W_BA1);
+	writel(~(VME_A32_SLV_SIZE-1), pci_reg_addr + W_AM1);
+	writel(VME_A32_SLV_LOCAL, pci_reg_addr + W_TA1);
+	writel(0x04, pci_reg_addr + W_IMG_CTRL1);
+
+	writel(0xF0000000, pci_reg_addr + W_BA2);
+	writel(0xFF000000, pci_reg_addr + W_AM2);
+	writel(VME_A24_SLV_LOCAL, pci_reg_addr + W_TA2);
+	writel(0x04, pci_reg_addr + W_IMG_CTRL2);
+
+	writel(0xFF000000, pci_reg_addr + W_BA3);
+	writel(0xFF000000, pci_reg_addr + W_AM3);
+	writel(VME_A16_SLV_LOCAL, pci_reg_addr + W_TA3);
+	writel(0x04, pci_reg_addr + W_IMG_CTRL3);
+
+	writel(0x00000001, pci_reg_addr + W_ERR_CS);
+	writel(0x00000001, pci_reg_addr + P_ERR_CS);
+
+	multiv_reset(vme_reg_addr);
+	writeb(readb(vme_reg_addr + VME_CTRL) | VME_CTRL_SHORT_D,
+		vme_reg_addr + VME_CTRL);
+
+	multiv_auto_slot_id(vme_reg_addr);
+
+	return 0;
+}

board/etin/kvme080/multiverse.h

@@ -0,0 +1,176 @@
+/*
+ * multiverse.h
+ *
+ * VME driver for Multiverse
+ *
+ * Author : Sangmoon Kim
+ *	    dogoil@etinsys.com
+ *
+ * Copyright 2005 ETIN SYSTEMS Co.,Ltd.
+ *
+ * This program is free software; you can redistribute	it and/or modify it
+ * under  the terms of	the GNU General Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#ifndef __MULTIVERSE_H__
+#define __MULTIVERSE_H__
+
+#define VME_A32_MSTR_BUS	0x90000000
+#define VME_A32_MSTR_SIZE	0x01000000
+
+#define VME_A32_SLV_SIZE	0x01000000
+
+#define VME_A32_SLV_BUS		0x90000000
+#define VME_A24_SLV_BUS		0x00000000
+#define VME_A16_SLV_BUS		0x00000000
+
+#define VME_A32_SLV_LOCAL	0x00000000
+#define VME_A24_SLV_LOCAL	0x00000000
+#define VME_A16_SLV_LOCAL	0x00000000
+
+#define A32_SLV_WINDOW
+#undef	A24_SLV_WINDOW
+#undef	A16_SLV_WINDOW
+#undef	REG_SLV_WINDOW
+
+/* PCI Registers */
+
+#define P_IMG_CTRL0		0x100
+#define P_BA0			0x104
+#define P_AM0			0x108
+#define P_TA0			0x10C
+#define P_IMG_CTRL1		0x110
+#define P_BA1			0x114
+#define P_AM1			0x118
+#define P_TA1			0x11C
+#define P_IMG_CTRL2		0x120
+#define P_BA2			0x124
+#define P_AM2			0x128
+#define P_TA2			0x12C
+#define P_IMG_CTRL3		0x130
+#define P_BA3			0x134
+#define P_AM3			0x138
+#define P_TA3			0x13C
+#define P_IMG_CTRL4		0x140
+#define P_BA4			0x144
+#define P_AM4			0x148
+#define P_TA4			0x14C
+#define P_IMG_CTRL5		0x150
+#define P_BA5			0x154
+#define P_AM5			0x158
+#define P_TA5			0x15C
+#define P_ERR_CS		0x160
+#define P_ERR_ADDR		0x164
+#define P_ERR_DATA		0x168
+
+#define WB_CONF_SPC_BAR		0x180
+#define W_IMG_CTRL1		0x184
+#define W_BA1			0x188
+#define W_AM1			0x18C
+#define W_TA1			0x190
+#define W_IMG_CTRL2		0x194
+#define W_BA2			0x198
+#define W_AM2			0x19C
+#define W_TA2			0x1A0
+#define W_IMG_CTRL3		0x1A4
+#define W_BA3			0x1A8
+#define W_AM3			0x1AC
+#define W_TA3			0x1B0
+#define W_IMG_CTRL4		0x1B4
+#define W_BA4			0x1B8
+#define W_AM4			0x1BC
+#define W_TA4			0x1C0
+#define W_IMG_CTRL5		0x1C4
+#define W_BA5			0x1C8
+#define W_AM5			0x1CC
+#define W_TA5			0x1D0
+#define W_ERR_CS		0x1D4
+#define W_ERR_ADDR		0x1D8
+#define W_ERR_DATA		0x1DC
+#define CNF_ADDR		0x1E0
+#define CNF_DATA		0x1E4
+#define INT_ACK			0x1E8
+#define ICR			0x1EC
+#define ISR			0x1F0
+
+/* VME registers */
+
+#define VME_SLAVE32_AM		0x03
+#define VME_SLAVE24_AM		0x02
+#define VME_SLAVE16_AM		0x01
+#define VME_SLAVE_REG_AM	0x00
+#define VME_SLAVE32_A		0x07
+#define VME_SLAVE24_A		0x06
+#define VME_SLAVE16_A		0x05
+#define VME_SLAVE_REG_A		0x04
+#define VME_SLAVE32_MASK	0x0B
+#define VME_SLAVE24_MASK	0x0A
+#define VME_SLAVE16_MASK	0x09
+#define VME_SLAVE_REG_MASK	0x08
+#define VME_SLAVE32_EN		0x0F
+#define VME_SLAVE24_EN		0x0E
+#define VME_SLAVE16_EN		0x0D
+#define VME_SLAVE_REG_EN	0x0C
+#define VME_MASTER32_AM		0x13
+#define VME_MASTER24_AM		0x12
+#define VME_MASTER16_AM		0x11
+#define VME_MASTER_REG_AM	0x10
+#define VME_RMW_ADRS		0x14
+#define VME_MBOX		0x18
+#define VME_STATUS		0x1E
+#define VME_CTRL		0x1C
+#define VME_IRQ			0x20
+#define VME_INT_EN		0x21
+#define VME_INT			0x22
+#define VME_IRQ1_REG		0x24
+#define VME_IRQ2_REG		0x28
+#define VME_IRQ3_REG		0x2C
+#define VME_IRQ4_REG		0x30
+#define VME_IRQ5_REG		0x34
+#define VME_IRQ6_REG		0x38
+#define VME_IRQ7_REG		0x3C
+
+/* VME control register */
+
+#define VME_CTRL_BRDRST		0x01
+#define VME_CTRL_SYSRST		0x02
+#define VME_CTRL_RMW		0x04
+#define VME_CTRL_SHORT_D	0x08
+#define VME_CTRL_SYSFAIL	0x10
+#define VME_CTRL_VOWN		0x20
+#define VME_CTRL_A16_REG_MODE	0x40
+
+/* VME status register */
+
+#define VME_STATUS_SYSCON	0x01
+#define VME_STATUS_SYSFAIL	0x02
+#define VME_STATUS_ACFAIL	0x04
+#define VME_STATUS_SYSRST	0x08
+#define VME_STATUS_VOWN		0x10
+
+/* Interrupt types */
+
+#define LVL1			0x0002
+#define LVL2			0x0004
+#define LVL3			0x0008
+#define LVL4			0x0010
+#define LVL5			0x0020
+#define LVL6			0x0040
+#define LVL7			0x0080
+#define MULTIVERSE_INTI_INT	0x0100
+#define MULTIVERSE_WB_INT	0x0200
+#define MULTIVERSE_PCI_INT	0x0400
+
+/* interrupt acknowledge */
+
+#define VME_IACK1		0x04
+#define VME_IACK2		0x08
+#define VME_IACK3		0x0c
+#define VME_IACK4		0x10
+#define VME_IACK5		0x14
+#define VME_IACK6		0x18
+#define VME_IACK7		0x1c
+
+#endif /* __MULTIVERSE_H__ */

board/etin/kvme080/u-boot.lds

@@ -0,0 +1,128 @@
+/*
+ * (C) Copyright 2001-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc824x/start.o	(.text)
+    lib_ppc/board.o	(.text)
+    lib_ppc/ppcstring.o	(.text)
+
+	. = DEFINED(env_offset) ? env_offset : .;
+    common/environment.o (.text)
+
+	*(.text)
+
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+
+  _end = . ;
+  PROVIDE (end = .);
+}

board/fads/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o lamp.o
+OBJS	= $(BOARD).o flash.o lamp.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/fads/fads.h

@@ -467,7 +467,9 @@
 #define CONFIG_ISO_PARTITION	1
 
 #undef	CONFIG_ATAPI
+#if 0	/* does not make sense when CFG_CMD_IDE is not enabled, too */
 #define CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card Adapter */
+#endif
 #undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
 #undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
 #undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/

board/fads/pcmcia.c

@@ -0,0 +1,84 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#ifdef	CONFIG_ADS
+#define	PCMCIA_BOARD_MSG "ADS"
+#else
+#define	PCMCIA_BOARD_MSG "FADS"
+#endif
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	u_long reg = 0;
+
+	switch(vpp) {
+		case 0: reg = 0; break;
+		case 50: reg = 1; break;
+		case 120: reg = 2; break;
+		default: return 1;
+	}
+
+	switch(vcc) {
+		case 0: reg = 0; break;
+#ifdef CONFIG_ADS
+	case 50: reg = BCSR1_PCCVCCON; break;
+#endif
+#ifdef CONFIG_FADS
+	case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break;
+	case 50: reg = BCSR1_PCCVCC1; break;
+#endif
+	default: return 1;
+	}
+
+	/* first, turn off all power */
+
+#ifdef CONFIG_ADS
+	*((uint *)BCSR1) |= BCSR1_PCCVCCON;
+#endif
+#ifdef CONFIG_FADS
+	*((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1);
+#endif
+	*((uint *)BCSR1) &= ~BCSR1_PCCVPP_MASK;
+
+	/* enable new powersettings */
+
+#ifdef CONFIG_ADS
+	*((uint *)BCSR1) &= ~reg;
+#endif
+#ifdef CONFIG_FADS
+	*((uint *)BCSR1) |= reg;
+#endif
+
+ 	*((uint *)BCSR1) |= reg << 20;
+
+	return 0;
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	*((uint *)BCSR1) &= ~BCSR1_PCCEN;
+	return 0;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	*((uint *)BCSR1) &= ~BCSR1_PCCEN;
+	return 0;
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+#endif	/* CONFIG_PCMCIA */

board/gth/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o ee_access.o
+OBJS	= $(BOARD).o flash.o ee_access.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/gth/pcmcia.c

@@ -0,0 +1,93 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "GTH COMPACT FLASH"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{	/* Do nothing */
+	return 0;
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+	volatile immap_t *immap;
+	volatile cpm8xx_t *cp;
+	volatile pcmconf8xx_t *pcmp;
+	volatile sysconf8xx_t *sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: GTH Slot %c\n", 'A' + slot);
+
+	immap = (immap_t *) CFG_IMMR;
+	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+	udelay (500);
+
+	/*
+	* Make sure there is a card in the slot,
+	* then configure the interface.
+	*/
+	udelay (10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__, __FUNCTION__,
+	       &(pcmp->pcmc_pipr), pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & 0x98000000) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	mask = PCMCIA_VS1 (slot) | PCMCIA_VS2 (slot);
+	reg = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+	       (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX (_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+
+	udelay (250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return 0;
+}
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	return 0;	/* No hardware to disable */
+}
+#endif
+
+#endif	/* CONFIG_PCMCIA */

board/gth2/config.mk

@@ -39,4 +39,3 @@ TEXT_BASE = 0x90000000
 endif
 endif
 endif
-

board/icu862/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/icu862/pcmcia.c

@@ -0,0 +1,268 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "ICU862"
+
+static void cfg_port_B (void)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	uint reg;
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure Port B for TPS2205 PC-Card Power-Interface Switch
+	*
+	* Switch off all voltages, assert shutdown
+	*/
+	reg  = cp->cp_pbdat;
+	reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+			TPS2205_VCC3    | TPS2205_VCC5    |	/* VAVCC => Hi-Z */
+			TPS2205_SHDN);				/* enable switch */
+	cp->cp_pbdat = reg;
+
+	cp->cp_pbpar &= ~(TPS2205_INPUTS | TPS2205_OUTPUTS);
+
+	reg = cp->cp_pbdir & ~(TPS2205_INPUTS);
+	cp->cp_pbdir = reg | TPS2205_OUTPUTS;
+
+	debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
+	       cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Port B for TPS2205 PC-Card Power-Interface Switch */
+	cfg_port_B ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	reg  = cp->cp_pbdat;
+	if ((pipr & mask) == mask) {
+		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+				TPS2205_VCC3);				/* 3V off	*/
+		reg &= ~(TPS2205_VCC5);				/* 5V on	*/
+		puts (" 5.0V card found: ");
+	} else {
+		reg |= (TPS2205_VPP_PGM | TPS2205_VPP_VCC |	/* VAVPP => Hi-Z */
+				TPS2205_VCC5);				/* 5V off	*/
+		reg &= ~(TPS2205_VCC3);				/* 3V on	*/
+		puts (" 3.3V card found: ");
+	}
+
+	debug ("\nPB DAT: %08x -> 3.3V %s 5.0V %s VPP_PGM %s VPP_VCC %s\n",
+	       reg,
+	       (reg & TPS2205_VCC3)    ? "off" : "on",
+	       (reg & TPS2205_VCC5)    ? "off" : "on",
+	       (reg & TPS2205_VPP_PGM) ? "off" : "on",
+	       (reg & TPS2205_VPP_VCC) ? "off" : "on" );
+
+	cp->cp_pbdat = reg;
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if ((cp->cp_pbdat & TPS2205_OC) == 0) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			cp->cp_pbdat &= ~(TPS2205_SHDN);
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* Shut down */
+	cp->cp_pbdat &= ~(TPS2205_SHDN);
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_port_B ();	/* Enables switch, but all in Hi-Z */
+
+	reg  = cp->cp_pbdat;
+
+	switch(vcc) {
+		case  0: 			break;	/* Switch off		*/
+		case 33: reg &= ~TPS2205_VCC3;	break;	/* Switch on 3.3V	*/
+		case 50: reg &= ~TPS2205_VCC5;	break;	/* Switch on 5.0V	*/
+		default: 			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	cp->cp_pbdat = reg;
+
+#ifdef DEBUG
+{
+	char *s;
+
+	if ((reg & TPS2205_VCC3) == 0) {
+		s = "at 3.3V";
+	} else if ((reg & TPS2205_VCC5) == 0) {
+		s = "at 5.0V";
+	} else {
+		s = "down";
+	}
+	printf ("PCMCIA powered %s\n", s);
+}
+#endif
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */

board/kup/common/pcmcia.c

@@ -0,0 +1,225 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "KUP"
+
+#define KUP4K_PCMCIA_B_3V3 (0x00020000)
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(slot);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(slot);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(2500);
+
+	/*
+	* Configure Port B pins for
+	* 3 Volts enable
+	*/
+	if (slot) { /* Slot A is built-in */
+		cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
+		cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+		/* remove all power */
+		cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
+	}
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	printf("%s  Slot %c:", slot ? "" : "\n", 'A' + slot);
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		puts (" 5.0V card found: NOT SUPPORTED !!!\n");
+	} else {
+		if(slot)
+			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+		puts (" 3.3V card found: ");
+	}
+#if 0
+	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
+	cp->cp_pbdir &= ~(0x0020 | 0x0010);
+	cp->cp_pbpar &= ~(0x0020 | 0x0010);
+	udelay(500000);
+#endif
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* remove all power */
+	if (slot)
+		cp->cp_pbdat |= KUP4K_PCMCIA_B_3V3;
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "	\
+			PCMCIA_BOARD_MSG	\
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	if (!slot) /* Slot A is not configurable */
+		return 0;
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(slot);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("PCMCIA power OFF\n");
+	/*
+	* Configure Port B pins for
+	* 3 Volts enable
+	*/
+	cp->cp_pbdir |=  KUP4K_PCMCIA_B_3V3;
+	cp->cp_pbpar &= ~KUP4K_PCMCIA_B_3V3;
+	/* remove all power */
+	cp->cp_pbdat |=  KUP4K_PCMCIA_B_3V3; /* active low */
+
+	switch(vcc) {
+		case  0: 		break;
+		case 33:
+			cp->cp_pbdat &= ~KUP4K_PCMCIA_B_3V3;
+			debug ("PCMCIA powered at 3.3V\n");
+			break;
+		case 50:
+			debug ("PCMCIA: 5Volt vcc not supported\n");
+			break;
+		default:
+			puts("PCMCIA: vcc not supported");
+			break;
+	}
+	udelay(10000);
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & (0x80000000 >> (slot << 4)))
+			       ? "only 5 V --> NOT SUPPORTED"
+	: "can do 3.3V");
+
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(slot);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(slot) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */

board/kup/kup4k/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/kup/kup4x/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o
+OBJS	= $(BOARD).o ../common/flash.o ../common/kup.o ../common/load_sernum_ethaddr.o ../common/pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/lwmon/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/lwmon/pcmcia.c

@@ -0,0 +1,240 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+#include <i2c.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "LWMON"
+
+/* #define's for MAX1604 Power Switch */
+#define MAX1604_OP_SUS		0x80
+#define MAX1604_VCCBON		0x40
+#define MAX1604_VCC_35		0x20
+#define MAX1604_VCCBHIZ		0x10
+#define MAX1604_VPPBON		0x08
+#define MAX1604_VPPBPBPGM	0x04
+#define MAX1604_VPPBHIZ		0x02
+/* reserved			0x01	*/
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+	uchar val;
+
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	/* Switch on PCMCIA port in PIC register 0x60 */
+	reg = pic_read  (0x60);
+	debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+	reg &= ~0x10;
+	/* reg |= 0x08; Vpp not needed */
+	pic_write (0x60, reg);
+#ifdef DEBUG
+	reg = pic_read  (0x60);
+	printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+#endif
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	 * Configure SIUMCR to enable PCMCIA port B
+	 * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	 */
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	 * Disable interrupts, DMA, and PCMCIA buffers
+	 * (isolate the interface) and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	 * Make sure there is a card in the slot, then configure the interface.
+	 */
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+		__LINE__,__FUNCTION__,
+		&(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	 * Power On.
+	 */
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+		reg,
+		(reg&PCMCIA_VS1(slot))?"n":"ff",
+		(reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		val = 0;		/* VCCB3/5 = 0 ==> use Vx = 5.0 V */
+		puts (" 5.0V card found: ");
+	} else {
+		val = MAX1604_VCC_35;	/* VCCB3/5 = 1 ==> use Vy = 3.3 V */
+		puts (" 3.3V card found: ");
+	}
+
+	/*  switch VCC on */
+	val |= MAX1604_OP_SUS | MAX1604_VCCBON;
+	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+	udelay(500000);
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	uchar val;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* remove all power, put output in high impedance state */
+	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
+	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	/* Switch off PCMCIA port in PIC register 0x60 */
+	reg = pic_read  (0x60);
+	debug ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+	reg |=  0x10;
+	reg &= ~0x08;
+	pic_write (0x60, reg);
+#ifdef DEBUG
+	reg = pic_read  (0x60);
+	printf ("[%d] PIC read: reg_60 = 0x%02x\n", __LINE__, reg);
+#endif
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	uchar val;
+
+	debug ("voltage_set: "
+		PCMCIA_BOARD_MSG
+		" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+		'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	 * Disable PCMCIA buffers (isolate the interface)
+	 * and assert RESET signal
+	 */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	 * Turn off all power (switch to high impedance)
+	 */
+	debug ("PCMCIA power OFF\n");
+	val  = MAX1604_VCCBHIZ | MAX1604_VPPBHIZ;
+	i2c_init  (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+
+	val = 0;
+	switch(vcc) {
+	case  0: 			break;
+	case 33: val = MAX1604_VCC_35;	break;
+	case 50: 			break;
+	default: 			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+		pcmp->pcmc_pipr,
+		(pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	i2c_write (CFG_I2C_POWER_A_ADDR, 0, 0, &val, 1);
+	if (val) {
+		debug ("PCMCIA powered at %sV\n",
+			(val & MAX1604_VCC_35) ? "3.3" : "5.0");
+	} else {
+		debug ("PCMCIA powered down\n");
+	}
+
+done:
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+		slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */

board/mbx8xx/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o vpd.o
+OBJS	= $(BOARD).o flash.o vpd.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/mbx8xx/pcmcia.c

@@ -0,0 +1,166 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#include "csr.h"
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+/* A lot of this has been taken from the RPX code in this file it works from me.
+   I have added the voltage selection for the MBX board. */
+
+/* MBX voltage bit in control register #2 */
+#define CR2_VPP12       ((uchar)0x10)
+#define CR2_VPPVDD      ((uchar)0x20)
+#define CR2_VDD5        ((uchar)0x40)
+#define CR2_VDD3        ((uchar)0x80)
+
+#define PCMCIA_BOARD_MSG "MBX860"
+
+int pcmcia_voltage_set (int slot, int vcc, int vpp)
+{
+	uchar reg = 0;
+
+	debug ("voltage_set: PCMCIA_BOARD_MSG Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	       'A' + slot, vcc / 10, vcc % 10, vpp / 10, vcc % 10);
+
+	switch (vcc) {
+		case 0:
+			break;
+		case 33:
+			reg |= CR2_VDD3;
+			break;
+		case 50:
+			reg |= CR2_VDD5;
+			break;
+		default:
+			return 1;
+	}
+
+	switch (vpp) {
+		case 0:
+			break;
+		case 33:
+		case 50:
+			if (vcc == vpp) {
+				reg |= CR2_VPPVDD;
+			} else {
+				return 1;
+			}
+			break;
+		case 120:
+			reg |= CR2_VPP12;
+			break;
+		default:
+			return 1;
+	}
+
+	/* first, turn off all power */
+	MBX_CSR2 &= ~(CR2_VDDSEL | CR2_VPPSEL);
+
+	/* enable new powersettings */
+	MBX_CSR2 |= reg;
+	debug ("MBX_CSR2 read = 0x%02x\n", MBX_CSR2);
+
+	return (0);
+}
+
+int pcmcia_hardware_enable (int slot)
+{
+	volatile immap_t *immap;
+	volatile cpm8xx_t *cp;
+	volatile pcmconf8xx_t *pcmp;
+	volatile sysconf8xx_t *sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n",
+	       'A' + slot);
+
+	udelay (10000);
+
+	immap = (immap_t *) CFG_IMMR;
+	sysp = (sysconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_siu_conf));
+	pcmp = (pcmconf8xx_t *) (&(((immap_t *) CFG_IMMR)->im_pcmcia));
+	cp = (cpm8xx_t *) (&(((immap_t *) CFG_IMMR)->im_cpm));
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr = PCMCIA_MASK (_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK (_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+	udelay (500);
+
+	/* remove all power */
+	pcmcia_voltage_set (slot, 0, 0);
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+#ifndef CONFIG_HMI10
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+#else
+	if (pcmp->pcmc_pipr & (0x10000000 >> (slot << 4))) {
+#endif	/* CONFIG_HMI10 */
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1 (_slot_) | PCMCIA_VS2 (_slot_);
+	reg = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n", reg,
+	       (reg & PCMCIA_VS1 (slot)) ? "n" : "ff",
+	       (reg & PCMCIA_VS2 (slot)) ? "n" : "ff");
+
+	if ((reg & mask) == mask) {
+		pcmcia_voltage_set (_slot_, 50, 0);
+		printf (" 5.0V card found: ");
+	} else {
+		pcmcia_voltage_set (_slot_, 33, 0);
+		printf (" 3.3V card found: ");
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg = PCMCIA_PGCRX (_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;	/* active low  */
+	PCMCIA_PGCRX (_slot_) = reg;
+
+	udelay (250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+	}
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable (int slot)
+{
+	return 0;	/* No hardware to disable */
+}
+#endif /* CFG_CMD_PCMCIA */
+
+#endif	/* CONFIG_PCMCIA */

board/mcc200/config.mk

@@ -26,16 +26,18 @@
 #
 #	Valid values for TEXT_BASE are:
 #
-#	0xFFF00000   boot high (standard configuration)
+#	0xFC000000   boot low (standard configuration)
-#	0xFE000000   boot low
+#	0xFFF00000   boot high
 #	0x00100000   boot from RAM (for testing only)
 #
 
 sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp
 
 ifndef TEXT_BASE
-## Standard: boot high
+## Standard: boot low
-TEXT_BASE = 0xFFF00000
+TEXT_BASE = 0xFC000000
+## Boot high
+# TEXT_BASE = 0xFFF00000
 ## For testing: boot from RAM
 # TEXT_BASE = 0x00100000
 endif

board/mcc200/mcc200.c

@@ -32,7 +32,12 @@
 /* #include "mt48lc8m32b2-6-7.h" */
 
 /* One MT48LC16M32S2 for 64 MB */
-#include "mt48lc16m32s2-75.h"
+/* #include "mt48lc16m32s2-75.h" */
+#if defined (CONFIG_MCC200_SDRAM)
+#include "mt48lc16m16a2-75.h"
+#else
+#include "mt46v16m16-75.h"
+#endif
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -249,7 +254,7 @@ int misc_init_r (void)
 		*(volatile int*)MPC5XXX_CS0_CFG |= (1 << 6);
 		flash_protect (FLAG_PROTECT_CLEAR,
 			       flash_info[0].start[0] + flash_info[0].size / 2,
-			       (flash_info[0].start[0] + flash_info[0].size) / 2 - 1,
+			       (flash_info[0].start[0] - 1) + flash_info[0].size,
 			       &flash_info[0]);
 		*(volatile int*)MPC5XXX_CS0_CFG &= ~(1 << 6);
 	}

board/netstar/crcek.S

@@ -13,6 +13,7 @@
  *	u32 - crc32
  */
 
+#include <config.h>
 #include "crcek.h"
 
 /**
@@ -39,7 +40,7 @@
 	.macro crcuj, offset, size
 	mov	r0, #0
 	ldr	r1, \offset
-	ldr	r2, [r1]
+	ldr	r2, [r1], #4
 	cmp	r2, r0		@ no data, no problem
 	beq	2f
 	tst	r2, #3		@ unaligned size
@@ -47,7 +48,6 @@
 	ldr	r3, \size
 	cmp	r2, r3		@ bogus size
 	bhi	2f
-	add	r1, r1, #4
 	do_crc32
 	ldr	r1, [r1]
 2:
@@ -55,16 +55,71 @@
 	.endm
 
 	.macro wait, reg
-	mov	\reg, #0x1000
+	mov	\reg, #0x100000
 3:
 	subs	\reg, \reg, #0x1
 	bne 	3b
-
 	.endm
+
 .text
 .globl crcek
 crcek:
-	b	crc2_bad
+	/* Enable I-cache */
+	mrc	p15, 0, r1, c0, c0, 0		@ read C15 ID register
+	mrc	p15, 0, r1, c0, c0, 1		@ read C15 Cache information register
+	mrc	p15, 0, r1, c1, c0, 0		@ read C15 Control register
+	orr	r1, r1, #0x1000			@ enable I-cache, map interrupt vector 0xffff0000
+	mcr	p15, 0, r1, c1, c0, 0		@ write C15 Control register
+	mov	r1, #0x00
+	mcr	p15, 0, r1, c7, c5, 0		@ Flush I-cache
+	nop
+	nop
+	nop
+	nop
+
+	/* Setup clocking mode */
+	ldr	r0, MPU_CLKM_BASE		@ base of CLOCK unit
+	ldrh	r1, [r0, #0x18]			@ ARM_SYST - get reset status
+	bic	r1, r1, #(7 << 11)		@ clear clock select
+	orr	r1, r1, #(2 << 11)		@ set synchronous scalable
+	mov	r2, #0
+loop:
+	cmp	r2, #1				@ this loop will wait for at least 100 cycles
+	streqh	r1, [r0, #0x18]			@ before issuing next request from MPU
+	add	r2, r2, #1			@ on the 1st run code is loaded into I-cache
+	cmp	r2, #16				@ and second run will set clocking mode
+	bne	loop
+	nop
+
+	/* Setup clock dividers */
+	ldr	r1, CKCTL_VAL
+	orr	r1, r1, #0x2000			@ enable DSP clock
+	strh	r1, [r0]			@ setup clock divisors
+
+	/* Setup DPLL to generate requested freq */
+	ldr	r0, DPLL1_BASE			@ base of DPLL1 register
+	mov	r1, #0x0010			@ set PLL_ENABLE
+	orr	r1, r1, #0x2000			@ set IOB to new locking
+	orr	r1, r1, #(OMAP5910_DPLL_MUL << 7) @ setup multiplier CLKREF
+	orr	r1, r1, #(OMAP5910_DPLL_DIV << 5) @ setup divider CLKREF
+	strh	r1, [r0]			@ write
+
+locking:
+	ldrh	r1, [r0]			@ get DPLL value
+	tst	r1, #0x01
+	beq	locking				@ while LOCK not set
+
+	/* Enable clock */
+	ldr	r0, MPU_CLKM_BASE		@ base of CLOCK unit
+	mov	r1, #(1 << 10)			@ disable idle mode do not check
+						@ nWAKEUP pin, other remain active
+	strh	r1, [r0, #0x04]
+	ldr	r1, EN_CLK_VAL
+	strh	r1, [r0, #0x08]
+	mov	r1, #0x003f			@ FLASH.RP not enabled in idle and
+	strh	r1, [r0, #0x0c]			@ max delayed ( 32 x CLKIN )
+
+
 	mov	r6, #0
 	crcuj	_LOADER1_OFFSET, _LOADER_SIZE
 	bne	crc1_bad
@@ -76,9 +131,8 @@ crc1_bad:
 crc2_bad:
 	ldr	r3, _LOADER1_OFFSET
 	ldr	r4, _LOADER2_OFFSET
-	b	boot_2nd
+	teq	r6, #3
-	tst	r6, #3
+	bne	one_is_bad	@ one of them (or both) has bad crc
-	beq	one_is_bad	@ one of them (or both) has bad crc
 	ldr	r1, [r3, #4]
 	ldr	r2, [r4, #4]
 	cmp	r1, r2		@ boot 2nd loader if versions differ
@@ -90,6 +144,7 @@ one_is_bad:
 	tst	r6, #2
 	bne	boot_2nd
 @ We are doomed, so let user know.
+hell:
 	ldr	r0, GPIO_BASE	@ configure GPIO pins
 	ldr	r1, GPIO_DIRECTION
 	strh	r1, [r0, #0x08]
@@ -171,6 +226,15 @@ CRC32_TABLE:
 
 GPIO_BASE:
 	.word 0xfffce000
+MPU_CLKM_BASE:
+	.word 0xfffece00
+DPLL1_BASE:
+	.word 0xfffecf00
+
+CKCTL_VAL:
+	.word OMAP5910_ARM_CKCTL
+EN_CLK_VAL:
+	.word OMAP5910_ARM_EN_CLK
 GPIO_DIRECTION:
 	.word 0x0000ffe7
 

board/netstar/crcit.c

@@ -77,7 +77,7 @@ int main(int argc, char **argv)
 	} else if ((argc == 4) && (strcmp(argv[1], "-v") == 0)) {
 		char *endptr, *nptr = argv[2];
 		unsigned ver = strtoul(nptr, &endptr, 0);
-		if (nptr != '\0' && endptr == '\0')
+		if (*nptr != '\0' && *endptr == '\0')
 			return doit(argv[3], ver);
 	}
 	fprintf(stderr, "Usage: crcit [-v version] <image>\n");

board/netstar/netstar.c

@@ -27,7 +27,6 @@ DECLARE_GLOBAL_DATA_PTR;
 int board_init(void)
 {
 	/* arch number of NetStar board */
-	/* TODO: use define from asm/mach-types.h */
 	gd->bd->bi_arch_number = 692;
 
 	/* adress of boot parameters */
@@ -51,15 +50,11 @@ int dram_init(void)
 	return 0;
 }
 
-extern void partition_flash(void);
-
 int misc_init_r(void)
 {
 	return 0;
 }
 
-extern void nand_init(void);
-
 int board_late_init(void)
 {
 	return 0;

board/netstar/setup.S

@@ -145,25 +145,23 @@ lowlevel_init:
 	nop
 
 	/* Setup clocking mode */
-	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ prepare base of CLOCK unit
+	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ base of CLOCK unit
-	ldrh	r1, [r0, #0x18]			@ get reset status
+	ldrh	r1, [r0, #0x18]			@ ARM_SYST - get reset status
 	bic	r1, r1, #(7 << 11)		@ clear clock select
 	orr	r1, r1, #(2 << 11)		@ set synchronous scalable
-	mov	r2, #0				@ set wait counter to 100 clock cycles
+	mov	r2, #0
-
+loop:
-icache_loop:
+	cmp	r2, #1				@ this loop will wait for at least 100 cycles
-	cmp	r2, #0x01
+	streqh	r1, [r0, #0x18]			@ before issuing next request from MPU
-	streqh	r1, [r0, #0x18]
+	add	r2, r2, #1			@ on the 1st run code is loaded into I-cache
-	add	r2, r2, #0x01
+	cmp	r2, #16				@ and second run will set clocking mode
-	cmp	r2, #0x10
+	bne	loop
-	bne	icache_loop
 	nop
 
-	/* Setup clock divisors */
+	/* Setup clock dividers */
-	ldr	r0, OMAP5910_MPU_CLKM_BASE	@ base of CLOCK unit
 	ldr	r1, _OMAP5910_ARM_CKCTL
 	orr	r1, r1, #0x2000			@ enable DSP clock
-	strh	r1, [r0, #0x00]			@ setup clock divisors
+	strh	r1, [r0]			@ setup clock divisors
 
 	/* Setup DPLL to generate requested freq */
 	ldr	r0, OMAP5910_DPLL1_BASE		@ base of DPLL1 register
@@ -186,8 +184,7 @@ locking:
 	ldr	r1, _OMAP5910_ARM_EN_CLK
 	strh	r1, [r0, #0x08]
 	mov	r1, #0x003f			@ FLASH.RP not enabled in idle and
-						@ max delayed ( 32 x CLKIN )
+	strh	r1, [r0, #0x0c]			@ max delayed ( 32 x CLKIN )
-	strh	r1, [r0, #0x0c]
 
 	/* Configure 5910 pins functions to match our board. */
 	ldr     r0, MUX_CONFIG_BASE

board/netta/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o dsp.o codec.o
+OBJS	= $(BOARD).o flash.o dsp.o codec.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/netta/pcmcia.c

@@ -0,0 +1,370 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+/* some sane bit macros */
+#define _BD(_b)				(1U << (31-(_b)))
+#define _BDR(_l, _h)			(((((1U << (31-(_l))) - 1) << 1) | 1) & ~((1U << (31-(_h))) - 1))
+
+#define _BW(_b)				(1U << (15-(_b)))
+#define _BWR(_l, _h)			(((((1U << (15-(_l))) - 1) << 1) | 1) & ~((1U << (15-(_h))) - 1))
+
+#define _BB(_b)				(1U << (7-(_b)))
+#define _BBR(_l, _h)			(((((1U << (7-(_l))) - 1) << 1) | 1) & ~((1U << (7-(_h))) - 1))
+
+#define _B(_b)				_BD(_b)
+#define _BR(_l, _h)			_BDR(_l, _h)
+
+#define PCMCIA_BOARD_MSG "NETTA"
+
+static const unsigned short vppd_masks[2] = { _BW(14), _BW(15) };
+
+static void cfg_vppd(int no)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
+		return;
+
+	mask = vppd_masks[no];
+
+	immap->im_ioport.iop_papar &= ~mask;
+	immap->im_ioport.iop_paodr &= ~mask;
+	immap->im_ioport.iop_padir |=  mask;
+}
+
+static void set_vppd(int no, int what)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vppd_masks)/sizeof(vppd_masks[0]))
+		return;
+
+	mask = vppd_masks[no];
+
+	if (what)
+		immap->im_ioport.iop_padat |= mask;
+	else
+		immap->im_ioport.iop_padat &= ~mask;
+}
+
+static const unsigned short vccd_masks[2] = { _BW(10), _BW(6) };
+
+static void cfg_vccd(int no)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
+		return;
+
+	mask = vccd_masks[no];
+
+	immap->im_ioport.iop_papar &= ~mask;
+	immap->im_ioport.iop_paodr &= ~mask;
+	immap->im_ioport.iop_padir |=  mask;
+}
+
+static void set_vccd(int no, int what)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	if ((unsigned int)no >= sizeof(vccd_masks)/sizeof(vccd_masks[0]))
+		return;
+
+	mask = vccd_masks[no];
+
+	if (what)
+		immap->im_ioport.iop_padat |= mask;
+	else
+		immap->im_ioport.iop_padat &= ~mask;
+}
+
+static const unsigned short oc_mask = _BW(8);
+
+static void cfg_oc(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask = oc_mask;
+
+	immap->im_ioport.iop_pcdir &= ~mask;
+	immap->im_ioport.iop_pcso  &= ~mask;
+	immap->im_ioport.iop_pcint &= ~mask;
+	immap->im_ioport.iop_pcpar &= ~mask;
+}
+
+static int get_oc(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask = oc_mask;
+	int what;
+
+	what = !!(immap->im_ioport.iop_pcdat & mask);;
+	return what;
+}
+
+static const unsigned short shdn_mask = _BW(12);
+
+static void cfg_shdn(void)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	mask = shdn_mask;
+
+	immap->im_ioport.iop_papar &= ~mask;
+	immap->im_ioport.iop_paodr &= ~mask;
+	immap->im_ioport.iop_padir |=  mask;
+}
+
+static void set_shdn(int what)
+{
+	volatile immap_t *immap = (immap_t *)CFG_IMMR;
+	unsigned short mask;
+
+	mask = shdn_mask;
+
+	if (what)
+		immap->im_ioport.iop_padat |= mask;
+	else
+		immap->im_ioport.iop_padat &= ~mask;
+}
+
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+
+	cfg_vppd(0); cfg_vppd(1);	/* VPPD0,VPPD1 VAVPP => Hi-Z */
+	cfg_vccd(0); cfg_vccd(1);	/* 3V and 5V off */
+	cfg_shdn();
+	cfg_oc();
+
+	/*
+	* Configure Port A for TPS2211 PC-Card Power-Interface Switch
+	*
+	* Switch off all voltages, assert shutdown
+	*/
+	set_vppd(0, 1); set_vppd(1, 1);
+	set_vccd(0, 0); set_vccd(1, 0);
+	set_shdn(1);
+
+	udelay(100000);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, pipr, mask;
+	int i;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	pipr = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       pipr,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+
+	if ((pipr & mask) == mask) {
+		set_vppd(0, 1); set_vppd(1, 1); 		/* VAVPP => Hi-Z */
+		set_vccd(0, 0); set_vccd(1, 1); 		/* 5V on, 3V off */
+		puts (" 5.0V card found: ");
+	} else {
+		set_vppd(0, 1); set_vppd(1, 1); 		/* VAVPP => Hi-Z */
+		set_vccd(0, 1); set_vccd(1, 0); 		/* 5V off, 3V on */
+		puts (" 3.3V card found: ");
+	}
+
+	/*  Wait 500 ms; use this to check for over-current */
+	for (i=0; i<5000; ++i) {
+		if (!get_oc()) {
+			printf ("   *** Overcurrent - Safety shutdown ***\n");
+			set_vccd(0, 0); set_vccd(1, 0); 		/* VAVPP => Hi-Z */
+			return (1);
+		}
+		udelay (100);
+	}
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	/* All voltages off / Hi-Z */
+	set_vppd(0, 1); set_vppd(1, 1);
+	set_vccd(0, 1); set_vccd(1, 1);
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+	ushort sreg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	sreg  = immap->im_ioport.iop_pcdat;
+	set_vppd(0, 1); set_vppd(1, 1);
+
+	switch(vcc) {
+		case  0:
+			break;	/* Switch off		*/
+
+		case 33:
+			set_vccd(0, 1); set_vccd(1, 0);
+			break;
+
+		case 50:
+			set_vccd(0, 0); set_vccd(1, 1);
+			break;
+
+		default:
+			goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+done:
+			debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */

board/ppmc7xx/config.mk

@@ -22,11 +22,6 @@
 # along with this program; if not, write to the Free Software
 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 # MA 02111-1307 USA
-#
-
-#
-# 
-#
 
 TEXT_BASE = 0xFFF00000
 TEXT_END  = 0xFFF40000

board/r360mpi/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	= $(BOARD).o flash.o
+OBJS	= $(BOARD).o flash.o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/r360mpi/pcmcia.c

@@ -0,0 +1,236 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "R360MPI"
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Ports A, B & C pins for
+	* 5 Volts Enable and 3 Volts enable
+	*/
+	immap->im_ioport.iop_pcpar &= ~(0x0400);
+	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
+	immap->im_ioport.iop_pcdir |= 0x0400;*/
+
+	immap->im_ioport.iop_papar &= ~(0x0200);/*
+	immap->im_ioport.iop_padir |= 0x0200;*/
+#if 0
+	immap->im_ioport.iop_pbpar &= ~(0xC000);
+	immap->im_ioport.iop_pbdir &= ~(0xC000);
+#endif
+	/* remove all power */
+
+	immap->im_ioport.iop_pcdat |= 0x0400;
+	immap->im_ioport.iop_padat |= 0x0200;
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		immap->im_ioport.iop_pcdat &= ~(0x4000);
+		puts (" 5.0V card found: ");
+	} else {
+		immap->im_ioport.iop_padat &= ~(0x0002);
+		puts (" 3.3V card found: ");
+	}
+	immap->im_ioport.iop_pcdir |= 0x0400;
+	immap->im_ioport.iop_padir |= 0x0200;
+#if 0
+	/*  VCC switch error flag, PCMCIA slot INPACK_ pin */
+	cp->cp_pbdir &= ~(0x0020 | 0x0010);
+	cp->cp_pbpar &= ~(0x0020 | 0x0010);
+	udelay(500000);
+#endif
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* remove all power */
+	immap->im_ioport.iop_pcdat |= 0x0400;
+	immap->im_ioport.iop_padat |= 0x0200;
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg |= __MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Ports A & C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn off all power
+	*/
+	debug ("PCMCIA power OFF\n");
+	immap->im_ioport.iop_pcpar &= ~(0x0400);
+	immap->im_ioport.iop_pcso  &= ~(0x0400);/*
+	immap->im_ioport.iop_pcdir |= 0x0400;*/
+
+	immap->im_ioport.iop_papar &= ~(0x0200);/*
+	immap->im_ioport.iop_padir |= 0x0200;*/
+
+	immap->im_ioport.iop_pcdat |= 0x0400;
+	immap->im_ioport.iop_padat |= 0x0200;
+
+	reg = 0;
+	switch(vcc) {
+		case  0: 		break;
+		case 33: reg |= 0x0200;	break;
+		case 50: reg |= 0x0400;	break;
+		default: 		goto done;
+	}
+
+	/* Checking supported voltages */
+
+	debug ("PIPR: 0x%x --> %s\n",
+	       pcmp->pcmc_pipr,
+	       (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
+
+	if (reg & 0x0200)
+		immap->im_ioport.iop_pcdat &= !reg;
+	if (reg & 0x0400)
+		immap->im_ioport.iop_padat &= !reg;
+	immap->im_ioport.iop_pcdir |= 0x0200;
+	immap->im_ioport.iop_padir |= 0x0400;
+	if (reg) {
+		debug ("PCMCIA powered at %sV\n",
+		       (reg&0x0400) ? "5.0" : "3.3");
+	} else {
+		debug ("PCMCIA powered down\n");
+	}
+
+done:
+			debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CCONFIG_PCMCIA */

board/sbc2410x/Makefile

@@ -0,0 +1,47 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	:= sbc2410x.o flash.o
+SOBJS	:= lowlevel_init.o
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) crv $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+-include .depend
+
+#########################################################################

board/sbc2410x/config.mk

@@ -0,0 +1,23 @@
+#
+# (C) Copyright 2002
+# Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+#
+# SAMSUNG SMDK2410 board with S3C2410X (ARM920T) cpu
+#
+# see http://www.samsung.com/ for more information on SAMSUNG
+#
+
+#
+# SMDK2410 has 1 bank of 64 MB DRAM
+#
+# 3000'0000 to 3400'0000
+#
+# Linux-Kernel is expected to be at 3000'8000, entry 3000'8000
+# optionally with a ramdisk at 3080'0000
+#
+# we load ourself to 33F8'0000
+#
+# download area is 3300'0000
+
+TEXT_BASE = 0x33F80000

board/sbc2410x/flash.c

@@ -0,0 +1,431 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+ulong myflush (void);
+
+#define FLASH_BANK_SIZE	PHYS_FLASH_SIZE
+#define MAIN_SECT_SIZE  0x10000	/* 64 KB */
+
+flash_info_t flash_info[CFG_MAX_FLASH_BANKS];
+
+#define CMD_READ_ARRAY		0x000000F0
+#define CMD_UNLOCK1		0x000000AA
+#define CMD_UNLOCK2		0x00000055
+#define CMD_ERASE_SETUP		0x00000080
+#define CMD_ERASE_CONFIRM	0x00000030
+#define CMD_PROGRAM		0x000000A0
+#define CMD_UNLOCK_BYPASS	0x00000020
+
+#define MEM_FLASH_ADDR1		(*(volatile u16 *)(CFG_FLASH_BASE + (0x00000555 << 1)))
+#define MEM_FLASH_ADDR2		(*(volatile u16 *)(CFG_FLASH_BASE + (0x000002AA << 1)))
+
+#define BIT_ERASE_DONE		0x00000080
+#define BIT_RDY_MASK		0x00000080
+#define BIT_PROGRAM_ERROR	0x00000020
+#define BIT_TIMEOUT		0x80000000	/* our flag */
+
+#define READY 1
+#define ERR   2
+#define TMO   4
+
+/*-----------------------------------------------------------------------
+ */
+
+ulong flash_init (void)
+{
+	int i, j;
+	ulong size = 0;
+
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i++) {
+		ulong flashbase = 0;
+
+		flash_info[i].flash_id =
+#if defined(CONFIG_AMD_LV400)
+			(AMD_MANUFACT & FLASH_VENDMASK) |
+			(AMD_ID_LV400B & FLASH_TYPEMASK);
+#elif defined(CONFIG_AMD_LV800)
+			(AMD_MANUFACT & FLASH_VENDMASK) |
+			(AMD_ID_LV800B & FLASH_TYPEMASK);
+#else
+#error "Unknown flash configured"
+#endif
+			flash_info[i].size = FLASH_BANK_SIZE;
+		flash_info[i].sector_count = CFG_MAX_FLASH_SECT;
+		memset (flash_info[i].protect, 0, CFG_MAX_FLASH_SECT);
+		if (i == 0)
+			flashbase = PHYS_FLASH_1;
+		else
+			panic ("configured too many flash banks!\n");
+		for (j = 0; j < flash_info[i].sector_count; j++) {
+			if (j <= 3) {
+				/* 1st one is 16 KB */
+				if (j == 0) {
+					flash_info[i].start[j] =
+						flashbase + 0;
+				}
+
+				/* 2nd and 3rd are both 8 KB */
+				if ((j == 1) || (j == 2)) {
+					flash_info[i].start[j] =
+						flashbase + 0x4000 + (j -
+								      1) *
+						0x2000;
+				}
+
+				/* 4th 32 KB */
+				if (j == 3) {
+					flash_info[i].start[j] =
+						flashbase + 0x8000;
+				}
+			} else {
+				flash_info[i].start[j] =
+					flashbase + (j - 3) * MAIN_SECT_SIZE;
+			}
+		}
+		size += flash_info[i].size;
+	}
+
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_FLASH_BASE,
+		       CFG_FLASH_BASE + monitor_flash_len - 1,
+		       &flash_info[0]);
+
+	flash_protect (FLAG_PROTECT_SET,
+		       CFG_ENV_ADDR,
+		       CFG_ENV_ADDR + CFG_ENV_SIZE - 1, &flash_info[0]);
+
+	return size;
+}
+
+/*-----------------------------------------------------------------------
+ */
+void flash_print_info (flash_info_t * info)
+{
+	int i;
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case (AMD_MANUFACT & FLASH_VENDMASK):
+		printf ("AMD: ");
+		break;
+	default:
+		printf ("Unknown Vendor ");
+		break;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case (AMD_ID_LV400B & FLASH_TYPEMASK):
+		printf ("1x Amd29LV400BB (4Mbit)\n");
+		break;
+	case (AMD_ID_LV800B & FLASH_TYPEMASK):
+		printf ("1x Amd29LV800BB (8Mbit)\n");
+		break;
+	default:
+		printf ("Unknown Chip Type\n");
+		goto Done;
+		break;
+	}
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20, info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+	for (i = 0; i < info->sector_count; i++) {
+		if ((i % 5) == 0) {
+			printf ("\n   ");
+		}
+		printf (" %08lX%s", info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+	}
+	printf ("\n");
+
+      Done:;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int flash_erase (flash_info_t * info, int s_first, int s_last)
+{
+	ushort result;
+	int iflag, cflag, prot, sect;
+	int rc = ERR_OK;
+	int chip;
+
+	/* first look for protection bits */
+
+	if (info->flash_id == FLASH_UNKNOWN)
+		return ERR_UNKNOWN_FLASH_TYPE;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		return ERR_INVAL;
+	}
+
+	if ((info->flash_id & FLASH_VENDMASK) !=
+	    (AMD_MANUFACT & FLASH_VENDMASK)) {
+		return ERR_UNKNOWN_FLASH_VENDOR;
+	}
+
+	prot = 0;
+	for (sect = s_first; sect <= s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+	if (prot)
+		return ERR_PROTECTED;
+
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	cflag = icache_status ();
+	icache_disable ();
+	iflag = disable_interrupts ();
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect <= s_last && !ctrlc (); sect++) {
+		printf ("Erasing sector %2d ... ", sect);
+
+		/* arm simple, non interrupt dependent timer */
+		reset_timer_masked ();
+
+		if (info->protect[sect] == 0) {	/* not protected */
+			vu_short *addr = (vu_short *) (info->start[sect]);
+
+			MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+			MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+			MEM_FLASH_ADDR1 = CMD_ERASE_SETUP;
+
+			MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+			MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+			*addr = CMD_ERASE_CONFIRM;
+
+			/* wait until flash is ready */
+			chip = 0;
+
+			do {
+				result = *addr;
+
+				/* check timeout */
+				if (get_timer_masked () >
+				    CFG_FLASH_ERASE_TOUT) {
+					MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
+					chip = TMO;
+					break;
+				}
+
+				if (!chip
+				    && (result & 0xFFFF) & BIT_ERASE_DONE)
+					chip = READY;
+
+				if (!chip
+				    && (result & 0xFFFF) & BIT_PROGRAM_ERROR)
+					chip = ERR;
+
+			} while (!chip);
+
+			MEM_FLASH_ADDR1 = CMD_READ_ARRAY;
+
+			if (chip == ERR) {
+				rc = ERR_PROG_ERROR;
+				goto outahere;
+			}
+			if (chip == TMO) {
+				rc = ERR_TIMOUT;
+				goto outahere;
+			}
+
+			printf ("ok.\n");
+		} else {	/* it was protected */
+
+			printf ("protected!\n");
+		}
+	}
+
+	if (ctrlc ())
+		printf ("User Interrupt!\n");
+
+      outahere:
+	/* allow flash to settle - wait 10 ms */
+	udelay_masked (10000);
+
+	if (iflag)
+		enable_interrupts ();
+
+	if (cflag)
+		icache_enable ();
+
+	return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash
+ */
+
+volatile static int write_hword (flash_info_t * info, ulong dest, ushort data)
+{
+	vu_short *addr = (vu_short *) dest;
+	ushort result;
+	int rc = ERR_OK;
+	int cflag, iflag;
+	int chip;
+
+	/*
+	 * Check if Flash is (sufficiently) erased
+	 */
+	result = *addr;
+	if ((result & data) != data)
+		return ERR_NOT_ERASED;
+
+
+	/*
+	 * Disable interrupts which might cause a timeout
+	 * here. Remember that our exception vectors are
+	 * at address 0 in the flash, and we don't want a
+	 * (ticker) exception to happen while the flash
+	 * chip is in programming mode.
+	 */
+	cflag = icache_status ();
+	icache_disable ();
+	iflag = disable_interrupts ();
+
+	MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+	MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+	MEM_FLASH_ADDR1 = CMD_UNLOCK_BYPASS;
+	*addr = CMD_PROGRAM;
+	*addr = data;
+
+	/* arm simple, non interrupt dependent timer */
+	reset_timer_masked ();
+
+	/* wait until flash is ready */
+	chip = 0;
+	do {
+		result = *addr;
+
+		/* check timeout */
+		if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+			chip = ERR | TMO;
+			break;
+		}
+		if (!chip && ((result & 0x80) == (data & 0x80)))
+			chip = READY;
+
+		if (!chip && ((result & 0xFFFF) & BIT_PROGRAM_ERROR)) {
+			result = *addr;
+
+			if ((result & 0x80) == (data & 0x80))
+				chip = READY;
+			else
+				chip = ERR;
+		}
+
+	} while (!chip);
+
+	*addr = CMD_READ_ARRAY;
+
+	if (chip == ERR || *addr != data)
+		rc = ERR_PROG_ERROR;
+
+	if (iflag)
+		enable_interrupts ();
+
+	if (cflag)
+		icache_enable ();
+
+	return rc;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash.
+ */
+
+int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
+{
+	ulong cp, wp;
+	int l;
+	int i, rc;
+	ushort data;
+
+	wp = (addr & ~1);	/* get lower word aligned address */
+
+	/*
+	 * handle unaligned start bytes
+	 */
+	if ((l = addr - wp) != 0) {
+		data = 0;
+		for (i = 0, cp = wp; i < l; ++i, ++cp) {
+			data = (data >> 8) | (*(uchar *) cp << 8);
+		}
+		for (; i < 2 && cnt > 0; ++i) {
+			data = (data >> 8) | (*src++ << 8);
+			--cnt;
+			++cp;
+		}
+		for (; cnt == 0 && i < 2; ++i, ++cp) {
+			data = (data >> 8) | (*(uchar *) cp << 8);
+		}
+
+		if ((rc = write_hword (info, wp, data)) != 0) {
+			return (rc);
+		}
+		wp += 2;
+	}
+
+	/*
+	 * handle word aligned part
+	 */
+	while (cnt >= 2) {
+		data = *((vu_short *) src);
+		if ((rc = write_hword (info, wp, data)) != 0) {
+			return (rc);
+		}
+		src += 2;
+		wp += 2;
+		cnt -= 2;
+	}
+
+	if (cnt == 0) {
+		return ERR_OK;
+	}
+
+	/*
+	 * handle unaligned tail bytes
+	 */
+	data = 0;
+	for (i = 0, cp = wp; i < 2 && cnt > 0; ++i, ++cp) {
+		data = (data >> 8) | (*src++ << 8);
+		--cnt;
+	}
+	for (; i < 2; ++i, ++cp) {
+		data = (data >> 8) | (*(uchar *) cp << 8);
+	}
+
+	return write_hword (info, wp, data);
+}

board/sbc2410x/lowlevel_init.S

@@ -0,0 +1,163 @@
+/*
+ * Memory Setup stuff - taken from blob memsetup.S
+ *
+ * Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
+ *                     Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
+ *
+ * Modified for the Samsung SMDK2410 by
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * Modified for the friendly-arm SBC-2410X by
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <version.h>
+
+/*
+ * Taken from linux/arch/arm/boot/compressed/head-s3c2410.S
+ *
+ * Copyright (C) 2002 Samsung Electronics SW.LEE  <hitchcar@sec.samsung.com>
+ */
+
+#define BWSCON	0x48000000
+
+/* BWSCON */
+#define DW8			(0x0)
+#define DW16			(0x1)
+#define DW32			(0x2)
+#define WAIT			(0x1<<2)
+#define UBLB			(0x1<<3)
+
+#define B1_BWSCON		(DW16)
+#define B2_BWSCON		(DW16)
+#define B3_BWSCON		(DW16 + WAIT + UBLB)
+#define B4_BWSCON		(DW16)
+#define B5_BWSCON		(DW16)
+#define B6_BWSCON		(DW32)
+#define B7_BWSCON		(DW32)
+
+#define B0_Tacs			0x0
+#define B0_Tcos			0x0
+#define B0_Tacc			0x7
+#define B0_Tcoh			0x0
+#define B0_Tah			0x0
+#define B0_Tacp			0x0
+#define B0_PMC			0x0
+
+#define B1_Tacs			0x0
+#define B1_Tcos			0x0
+#define B1_Tacc			0x7
+#define B1_Tcoh			0x0
+#define B1_Tah			0x0
+#define B1_Tacp			0x0
+#define B1_PMC			0x0
+
+#define B2_Tacs			0x0
+#define B2_Tcos			0x0
+#define B2_Tacc			0x7
+#define B2_Tcoh			0x0
+#define B2_Tah			0x0
+#define B2_Tacp			0x0
+#define B2_PMC			0x0
+
+#define B3_Tacs			0xc
+#define B3_Tcos			0x7
+#define B3_Tacc			0xf
+#define B3_Tcoh			0x1
+#define B3_Tah			0x0
+#define B3_Tacp			0x0
+#define B3_PMC			0x0
+
+#define B4_Tacs			0x0
+#define B4_Tcos			0x0
+#define B4_Tacc			0x7
+#define B4_Tcoh			0x0
+#define B4_Tah			0x0
+#define B4_Tacp			0x0
+#define B4_PMC			0x0
+
+#define B5_Tacs			0xc
+#define B5_Tcos			0x7
+#define B5_Tacc			0xf
+#define B5_Tcoh			0x1
+#define B5_Tah			0x0
+#define B5_Tacp			0x0
+#define B5_PMC			0x0
+
+#define B6_MT			0x3	/* SDRAM */
+#define B6_Trcd			0x1
+#define B6_SCAN			0x1	/* 9bit */
+
+#define B7_MT			0x3	/* SDRAM */
+#define B7_Trcd			0x1	/* 3clk */
+#define B7_SCAN			0x1	/* 9bit */
+
+/* REFRESH parameter */
+#define REFEN			0x1	/* Refresh enable */
+#define TREFMD			0x0	/* CBR(CAS before RAS)/Auto refresh */
+#define Trp			0x0	/* 2clk */
+#define Trc			0x3	/* 7clk */
+#define Tchr			0x2	/* 3clk */
+#define REFCNT			0x0459
+/**************************************/
+
+_TEXT_BASE:
+	.word	TEXT_BASE
+
+.globl lowlevel_init
+lowlevel_init:
+	/* memory control configuration */
+	/* make r0 relative the current location so that it */
+	/* reads SMRDATA out of FLASH rather than memory ! */
+	ldr     r0, =SMRDATA
+	ldr	r1, _TEXT_BASE
+	sub	r0, r0, r1
+	ldr	r1, =BWSCON	/* Bus Width Status Controller */
+	add     r2, r0, #13*4
+0:
+	ldr     r3, [r0], #4
+	str     r3, [r1], #4
+	cmp     r2, r0
+	bne     0b
+
+	/* everything is fine now */
+	mov	pc, lr
+
+	.ltorg
+/* the literal pools origin */
+
+SMRDATA:
+    .word (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))
+    .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC))
+    .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC))
+    .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC))
+    .word ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC))
+    .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC))
+    .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC))
+    .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))
+    .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
+    .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
+    .word 0xb2
+    .word 0x30
+    .word 0x30

board/sbc2410x/sbc2410x.c

@@ -0,0 +1,183 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
+ *
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <s3c2410.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+#include <linux/mtd/nand.h>
+#endif
+
+/* ------------------------------------------------------------------------- */
+
+#define FCLK_SPEED 1
+
+#if FCLK_SPEED==0		/* Fout = 203MHz, Fin = 12MHz for Audio */
+#define M_MDIV	0xC3
+#define M_PDIV	0x4
+#define M_SDIV	0x1
+#elif FCLK_SPEED==1		/* Fout = 202.8MHz */
+#define M_MDIV	0x5c
+#define M_PDIV	0x4
+#define M_SDIV	0x0
+#endif
+
+#define USB_CLOCK 1
+
+#if USB_CLOCK==0
+#define U_M_MDIV	0xA1
+#define U_M_PDIV	0x3
+#define U_M_SDIV	0x1
+#elif USB_CLOCK==1
+#define U_M_MDIV	0x48
+#define U_M_PDIV	0x3
+#define U_M_SDIV	0x2
+#endif
+
+static inline void delay (unsigned long loops)
+{
+	__asm__ volatile ("1:\n"
+			  "subs %0, %1, #1\n"
+			  "bne 1b":"=r" (loops):"0" (loops));
+}
+
+/*
+ * Miscellaneous platform dependent initialisations
+ */
+
+int board_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+	S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+	/* to reduce PLL lock time, adjust the LOCKTIME register */
+	clk_power->LOCKTIME = 0xFFFFFF;
+
+	/* configure MPLL */
+	clk_power->MPLLCON = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV);
+
+	/* some delay between MPLL and UPLL */
+	delay (4000);
+
+	/* configure UPLL */
+	clk_power->UPLLCON = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV);
+
+	/* some delay between MPLL and UPLL */
+	delay (8000);
+
+	/* set up the I/O ports */
+	gpio->GPACON = 0x007FFFFF;
+	gpio->GPBCON = 0x00044556;
+	gpio->GPBUP = 0x000007FF;
+	gpio->GPCCON = 0xAAAAAAAA;
+	gpio->GPCUP = 0x0000FFFF;
+	gpio->GPDCON = 0xAAAAAAAA;
+	gpio->GPDUP = 0x0000FFFF;
+	gpio->GPECON = 0xAAAAAAAA;
+	gpio->GPEUP = 0x0000FFFF;
+	gpio->GPFCON = 0x000055AA;
+	gpio->GPFUP = 0x000000FF;
+	gpio->GPGCON = 0xFF95FF3A;
+	gpio->GPGUP = 0x0000FFFF;
+	gpio->GPHCON = 0x0016FAAA;
+	gpio->GPHUP = 0x000007FF;
+
+	gpio->EXTINT0=0x22222222;
+	gpio->EXTINT1=0x22222222;
+	gpio->EXTINT2=0x22222222;
+
+	/* arch number of SMDK2410-Board */
+	gd->bd->bi_arch_number = MACH_TYPE_SMDK2410;
+
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = 0x30000100;
+
+	icache_enable();
+	dcache_enable();
+
+	return 0;
+}
+
+int dram_init (void)
+{
+	DECLARE_GLOBAL_DATA_PTR;
+
+	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
+	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
+
+	return 0;
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_NAND)
+extern ulong nand_probe(ulong physadr);
+
+static inline void NF_Reset(void)
+{
+	int i;
+
+	NF_SetCE(NFCE_LOW);
+	NF_Cmd(0xFF);		/* reset command */
+	for(i = 0; i < 10; i++);	/* tWB = 100ns. */
+	NF_WaitRB();		/* wait 200~500us; */
+	NF_SetCE(NFCE_HIGH);
+}
+
+static inline void NF_Init(void)
+{
+#if 1
+#define TACLS   0
+#define TWRPH0  3
+#define TWRPH1  0
+#else
+#define TACLS   0
+#define TWRPH0  4
+#define TWRPH1  2
+#endif
+
+	NF_Conf((1<<15)|(0<<14)|(0<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0));
+	/*nand->NFCONF = (1<<15)|(1<<14)|(1<<13)|(1<<12)|(1<<11)|(TACLS<<8)|(TWRPH0<<4)|(TWRPH1<<0); */
+	/* 1  1    1     1,   1      xxx,  r xxx,   r xxx */
+	/* En 512B 4step ECCR nFCE=H tACLS   tWRPH0   tWRPH1 */
+
+	NF_Reset();
+}
+
+void nand_init(void)
+{
+	S3C2410_NAND * const nand = S3C2410_GetBase_NAND();
+
+	NF_Init();
+#ifdef DEBUG
+	printf("NAND flash probing at 0x%.8lX\n", (ulong)nand);
+#endif
+	printf ("%4lu MB\n", nand_probe((ulong)nand) >> 20);
+}
+#endif /* CONFIG_COMMANDS & CFG_CMD_NAND */

board/sbc2410x/u-boot.lds

@@ -0,0 +1,56 @@
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <gj@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+/*OUTPUT_FORMAT("elf32-arm", "elf32-arm", "elf32-arm")*/
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	. = 0x00000000;
+
+	. = ALIGN(4);
+	.text      :
+	{
+	  cpu/arm920t/start.o	(.text)
+	  *(.text)
+	}
+
+	. = ALIGN(4);
+	.rodata : { *(.rodata) }
+
+	. = ALIGN(4);
+	.data : { *(.data) }
+
+	. = ALIGN(4);
+	.got : { *(.got) }
+
+	__u_boot_cmd_start = .;
+	.u_boot_cmd : { *(.u_boot_cmd) }
+	__u_boot_cmd_end = .;
+
+	. = ALIGN(4);
+	__bss_start = .;
+	.bss : { *(.bss) }
+	_end = .;
+}

board/spc1920/Makefile

@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2000
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $(OBJS)
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################

board/spc1920/config.mk

@@ -0,0 +1,35 @@
+#
+# (C) Copyright 2000-2004
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# Motorola old MPC821/860ADS, MPC8xxFADS, new MPC866ADS, and
+# MPC885ADS boards
+#
+
+#TEXT_BASE = 0xFE000000
+TEXT_BASE = 0xFFF00000
+PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/spc1920
+HOST_CFLAGS += -I$(TOPDIR)/board/spc1920
+HOST_ENVIRO_CFLAGS += -I$(TOPDIR)/board/spc1920

board/spc1920/pld.h

@@ -0,0 +1,14 @@
+#ifndef __PLD_H__
+#define __PLD_H__
+
+typedef struct spc1920_pld {
+	uchar com1_en;
+	uchar dsp_reset;
+	uchar dsp_hpi_on;
+	uchar codec_dsp_power_en;
+	uchar clk2_en;
+	uchar clk3_select;
+	uchar clk4_select;
+} spc1920_pld_t;
+
+#endif /* __PLD_H__ */

board/spc1920/spc1920.c

@@ -0,0 +1,236 @@
+/*
+ * (C) Copyright 2000-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <common.h>
+#include <mpc8xx.h>
+#include "pld.h"
+
+#define	_NOT_USED_	0xFFFFFFFF
+/* #define debug(fmt,args...)     printf (fmt ,##args) */
+
+static long int dram_size (long int, long int *, long int);
+
+const uint sdram_table[] = {
+	/*
+	 * Single Read. (Offset 0 in UPMB RAM)
+	 */
+	0x1F07FC04, 0xEEAEFC04, 0x11ADFC04, 0xEFBBBC00,
+	0x1FF77C47, /* last */
+	/*
+	 * SDRAM Initialization (offset 5 in UPMB RAM)
+	 *
+	 * This is no UPM entry point. The following definition uses
+	 * the remaining space to establish an initialization
+	 * sequence, which is executed by a RUN command.
+	 *
+	 */
+	0x1FF77C34, 0xEFEABC34, 0x1FB57C35, /* last */
+	/*
+	 * Burst Read. (Offset 8 in UPMB RAM)
+	 */
+	0x1F07FC04, 0xEEAEFC04, 0x10ADFC04, 0xF0AFFC00,
+	0xF0AFFC00, 0xF1AFFC00, 0xEFBBBC00, 0x1FF77C47, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Single Write. (Offset 18 in UPMB RAM)
+	 */
+	0x1F07FC04, 0xEEAEBC00, 0x01B93C04, 0x1FF77C47, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Burst Write. (Offset 20 in UPMB RAM)
+	 */
+	0x1F07FC04, 0xEEAEBC00, 0x10AD7C00, 0xF0AFFC00,
+	0xF0AFFC00, 0xE1BBBC04, 0x1FF77C47, /* last */
+	_NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Refresh  (Offset 30 in UPMB RAM)
+	 */
+	0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+	0xFFFFFC84, 0xFFFFFC07, /* last */
+	_NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Exception. (Offset 3c in UPMB RAM)
+	 */
+	0x7FFFFC07, /* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+long int initdram (int board_type)
+{
+	volatile immap_t *immr = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immr->im_memctl;
+	/* volatile spc1920_pld_t *pld = (spc1920_pld_t *) CFG_SPC1920_PLD_BASE; */
+
+	long int size_b0;
+	long int size8, size9;
+	int i;
+
+	/*
+	 * Configure UPMB for SDRAM
+	 */
+	upmconfig (UPMB, (uint *)sdram_table, sizeof(sdram_table)/sizeof(uint));
+
+	udelay(100);
+
+	memctl->memc_mptpr = CFG_MPTPR;
+
+	/* burst length=4, burst type=sequential, CAS latency=2 */
+	memctl->memc_mar = CFG_MAR;
+
+	/*
+	 * Map controller bank 1 to the SDRAM bank at preliminary address.
+	 */
+	memctl->memc_or1 = CFG_OR1_PRELIM;
+	memctl->memc_br1 = CFG_BR1_PRELIM;
+
+	/* initialize memory address register */
+	memctl->memc_mbmr = CFG_MBMR_8COL; /* refresh not enabled yet */
+
+	/* mode initialization (offset 5) */
+	udelay (200);				/* 0x80006105 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x05);
+
+	/* run 2 refresh sequence with 4-beat refresh burst (offset 0x30) */
+	udelay (1);				/* 0x80006130 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
+	udelay (1);				/* 0x80006130 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x30);
+	udelay (1);				/* 0x80006106 */
+	memctl->memc_mcr = MCR_OP_RUN | MCR_UPM_B | MCR_MB_CS1 | MCR_MLCF (1) | MCR_MAD (0x06);
+
+	memctl->memc_mbmr |= MBMR_PTBE;	/* refresh enabled */
+
+	udelay (200);
+
+	/* Need at least 10 DRAM accesses to stabilize */
+	for (i = 0; i < 10; ++i) {
+		volatile unsigned long *addr =
+			(volatile unsigned long *) CFG_SDRAM_BASE;
+		unsigned long val;
+
+		val = *(addr + i);
+		*(addr + i) = val;
+	}
+
+	/*
+	 * Check Bank 0 Memory Size for re-configuration
+	 *
+	 * try 8 column mode
+	 */
+	size8 = dram_size (CFG_MBMR_8COL, (long *)CFG_SDRAM_BASE, SDRAM_MAX_SIZE);
+
+	udelay (1000);
+
+	/*
+	 * try 9 column mode
+	 */
+	size9 = dram_size (CFG_MBMR_9COL, (long *)CFG_SDRAM_BASE, SDRAM_MAX_SIZE);
+
+	if (size8 < size9) {		/* leave configuration at 9 columns */
+		size_b0 = size9;
+		memctl->memc_mbmr = CFG_MBMR_9COL | MBMR_PTBE;
+		udelay (500);
+	} else {			/* back to 8 columns            */
+		size_b0 = size8;
+		memctl->memc_mbmr = CFG_MBMR_8COL | MBMR_PTBE;
+		udelay (500);
+	}
+
+	/*
+	 * Final mapping:
+	 */
+
+	memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) |
+			OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING;
+	memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMB | BR_V;
+	udelay (1000);
+
+
+	/* PLD Setup */
+	memctl->memc_or5 = CFG_OR5_PRELIM;
+	memctl->memc_br5 = CFG_BR5_PRELIM;
+	udelay(1000);
+
+	return (size_b0);
+}
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+static long int dram_size (long int mbmr_value, long int *base,
+			   long int maxsize)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+	memctl->memc_mbmr = mbmr_value;
+
+	return (get_ram_size (base, maxsize));
+}
+
+
+/************* other stuff ******************/
+
+
+int board_early_init_f(void)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+
+
+	/* Turn on LED PD9 */
+	immap->im_ioport.iop_pdpar &= ~(0x0040);
+	immap->im_ioport.iop_pddir |= 0x0040;
+	immap->im_ioport.iop_pddat |= 0x0040;
+
+	/* Enable PD10 (COM2_EN) */
+	immap->im_ioport.iop_pdpar &= ~0x0020;
+	immap->im_ioport.iop_pddir &= ~0x4000;
+	immap->im_ioport.iop_pddir |= 0x0020;
+	immap->im_ioport.iop_pddat |= 0x0020;
+
+
+#ifdef CFG_SMC1_PLD_CLK4 /* SMC1 uses CLK4 from PLD */
+	immap->im_cpm.cp_simode |= 0x7000;
+	immap->im_cpm.cp_simode &= ~(0x8000);
+#endif
+
+	return 0;
+}
+
+
+int checkboard (void)
+{
+	puts("Board: SPC1920\n");
+	return 0;
+}

board/spc1920/u-boot.lds

@@ -0,0 +1,144 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/mpc8xx/start.o		(.text)
+    cpu/mpc8xx/traps.o		(.text)
+    common/dlmalloc.o		(.text)
+    lib_ppc/ppcstring.o		(.text)
+    lib_generic/vsprintf.o	(.text)
+    lib_generic/crc32.o		(.text)
+    lib_generic/zlib.o		(.text)
+    lib_ppc/cache.o		(.text)
+    lib_ppc/time.o		(.text)
+
+    . = DEFINED(env_offset) ? env_offset : .;
+    common/environment.o	(.ppcenv)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+    *(.eh_frame)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}

board/tqm5200/Makefile

@@ -25,7 +25,7 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-OBJS	:= $(BOARD).o cmd_stk52xx.o
+OBJS	:= $(BOARD).o cmd_stk52xx.o cmd_tb5200.o
 
 $(LIB):	$(OBJS) $(SOBJS)
 	$(AR) crv $@ $(OBJS)

board/tqm5200/cmd_stk52xx.c

@@ -22,7 +22,7 @@
  */
 
 /*
- * SKT52XX specific functions
+ * STK52XX specific functions
  */
 /*#define DEBUG*/
 
@@ -30,6 +30,7 @@
 #include <command.h>
 
 #if (CONFIG_COMMANDS & CFG_CMD_BSP)
+#if defined (CONFIG_STK52XX)
 
 #define DEFAULT_VOL	45
 #define DEFAULT_FREQ	500
@@ -60,7 +61,6 @@ static int spi_transmit(unsigned char data);
 static void pcm1772_write_reg(unsigned char addr, unsigned char data);
 static void set_attenuation(unsigned char attenuation);
 
-#ifdef CONFIG_STK52XX
 static void spi_init(void)
 {
 	struct mpc5xxx_spi *spi = (struct mpc5xxx_spi*)MPC5XXX_SPI;
@@ -1209,7 +1209,7 @@ U_BOOT_CMD(
 	fkt ,	4,	1,	cmd_fkt,
 	"fkt     - Function test routines\n",
 	"led number on/off\n"
-	"     - 'number's like printed on SKT52XX board\n"
+	"     - 'number's like printed on STK52XX board\n"
 	"fkt can\n"
 	"     - loopback plug for X83 required\n"
 	"fkt rs232 number\n"

board/tqm5200/cmd_tb5200.c

@@ -0,0 +1,104 @@
+/*
+ * (C) Copyright 2005 - 2006
+ * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * TB5200 specific functions
+ */
+/*#define DEBUG*/
+
+#include <common.h>
+#include <command.h>
+
+#if (CONFIG_COMMANDS & CFG_CMD_BSP)
+#if defined (CONFIG_TB5200)
+
+#define SM501_PANEL_DISPLAY_CONTROL	0x00080000UL
+
+static void led_init(void)
+{
+	struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
+
+	/* configure timer 4 for simple GPIO output */
+	gpt->gpt4.emsr |=  0x00000024;
+}
+
+int cmd_led(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	struct mpc5xxx_gpt_0_7 *gpt = (struct mpc5xxx_gpt_0_7 *)MPC5XXX_GPT;
+
+	led_init();
+
+	if (strcmp (argv[1], "on") == 0) {
+		debug ("switch status LED on\n");
+		gpt->gpt4.emsr |=  (1 << 4);
+	} else if (strcmp (argv[1], "off") == 0) {
+		debug ("switch status LED off\n");
+		gpt->gpt4.emsr &=  ~(1 << 4);
+	} else {
+		printf ("Usage:\nled on/off\n");
+		return 1;
+	}
+
+	return 0;
+}
+
+static void sm501_backlight (unsigned int state)
+{
+	if (state == 1) {
+		*(vu_long *)(SM501_MMIO_BASE+SM501_PANEL_DISPLAY_CONTROL) |=
+			(1 << 26) | (1 << 27);
+	} else if (state == 0)
+		*(vu_long *)(SM501_MMIO_BASE+SM501_PANEL_DISPLAY_CONTROL) &=
+			~((1 << 26) | (1 << 27));
+}
+
+int cmd_backlight(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+	if (strcmp (argv[1], "on") == 0) {
+		debug ("switch backlight on\n");
+		sm501_backlight (1);
+	} else if (strcmp (argv[1], "off") == 0) {
+		debug ("switch backlight off\n");
+		sm501_backlight (0);
+	} else {
+		printf ("Usage:\nbacklight on/off\n");
+		return 1;
+	}
+
+	return 0;
+}
+
+U_BOOT_CMD(
+	led ,	2,	1,	cmd_led,
+	"led     - switch status LED on or off\n",
+	"on/off\n"
+);
+
+U_BOOT_CMD(
+	backlight ,	2,	1,	cmd_backlight,
+	"backlight - switch backlight on or off\n",
+	"on/off\n"
+	);
+
+#endif /* CONFIG_STK52XX */
+#endif /* CFG_CMD_BSP */

board/tqm5200/config.mk

@@ -28,12 +28,17 @@
 #
 #	0xFC000000   boot low (standard configuration with room for max 64 MByte
 #		     Flash ROM)
+#	0xFFF00000   boot high (for a backup copy of U-Boot)
 #	0x00100000   boot from RAM (for testing only)
 #
 
+sinclude $(TOPDIR)/board/$(BOARDDIR)/config.tmp
+
 ifndef TEXT_BASE
 ## Standard: boot low
 TEXT_BASE = 0xFC000000
+## For a backup copy of U-Boot at the end of flash: boot high
+# TEXT_BASE = 0xFFF00000
 ## For testing: boot from RAM
 # TEXT_BASE = 0x00100000
 endif

board/tqm5200/tqm5200.c

@@ -1,11 +1,11 @@
 /*
- * (C) Copyright 2003-2004
+ * (C) Copyright 2003-2006
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * (C) Copyright 2004
  * Mark Jonas, Freescale Semiconductor, mark.jonas@motorola.com.
  *
- * (C) Copyright 2004-2005
+ * (C) Copyright 2004-2006
  * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
  *
  * See file CREDITS for list of people who contributed to this
@@ -30,6 +30,7 @@
 #include <common.h>
 #include <mpc5xxx.h>
 #include <pci.h>
+#include <asm/processor.h>
 
 #ifdef CONFIG_VIDEO_SM501
 #include <sm501.h>
@@ -101,6 +102,8 @@ long int initdram (int board_type)
 {
 	ulong dramsize = 0;
 	ulong dramsize2 = 0;
+	uint svr, pvr;
+
 #ifndef CFG_RAMBOOT
 	ulong test1, test2;
 
@@ -190,11 +193,31 @@ long int initdram (int board_type)
 	} else {
 		dramsize2 = 0;
 	}
-
 #endif /* CFG_RAMBOOT */
 
-/*	return dramsize + dramsize2; */
+	/*
+	 * On MPC5200B we need to set the special configuration delay in the
+	 * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
+	 * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
+	 *
+	 * "The SDelay should be written to a value of 0x00000004. It is
+	 * required to account for changes caused by normal wafer processing
+	 * parameters."
+	 */
+	svr = get_svr();
+	pvr = get_pvr();
+	if ((SVR_MJREV(svr) >= 2) &&
+	    (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
+
+		*(vu_long *)MPC5XXX_SDRAM_SDELAY = 0x04;
+		__asm__ volatile ("sync");
+	}
+
+#if defined(CONFIG_TQM5200_B)
+	return dramsize + dramsize2;
+#else
 	return dramsize;
+#endif /* CONFIG_TQM5200_B */
 }
 
 #elif defined(CONFIG_MGT5100)
@@ -250,20 +273,36 @@ long int initdram (int board_type)
 
 int checkboard (void)
 {
-#if defined (CONFIG_AEVFIFO)
+#if defined(CONFIG_AEVFIFO)
 	puts ("Board: AEVFIFO\n");
 	return 0;
 #endif
-#if defined (CONFIG_TQM5200)
+
-	puts ("Board: TQM5200 (TQ-Components GmbH)\n");
+#if defined(CONFIG_TQM5200S)
+# define MODULE_NAME	"TQM5200S"
+#else
+# define MODULE_NAME	"TQM5200"
 #endif
-#if defined (CONFIG_STK52XX)
+
-	puts ("       on a STK52XX baseboard\n");
+#if defined(CONFIG_STK52XX)
+# define CARRIER_NAME	"STK52xx"
+#elif defined(CONFIG_TB5200)
+# define CARRIER_NAME	"TB5200"
+#elif defined(CONFIG_CAM5200)
+# define CARRIER_NAME	"Cam5200"
+#else
+# error "Unknown carrier board"
 #endif
 
+	puts (	"Board: " MODULE_NAME " (TQ-Components GmbH)\n"
+		"       on a " CARRIER_NAME " carrier board\n");
+
 	return 0;
 }
 
+#undef MODULE_NAME
+#undef CARRIER_NAME
+
 void flash_preinit(void)
 {
 	/*
@@ -405,7 +444,6 @@ int board_early_init_r (void)
 #endif
 #endif /* CONFIG_PS2MULT */
 
-#if defined(CONFIG_CS_AUTOCONF)
 int last_stage_init (void)
 {
 	/*
@@ -500,7 +538,6 @@ int last_stage_init (void)
 
 	return 0;
 }
-#endif /* CONFIG_CS_AUTOCONF */
 
 #ifdef CONFIG_VIDEO_SM501
 
@@ -567,9 +604,14 @@ void video_get_info_str (int line_number, char *info)
 {
 	if (line_number == 1) {
 	strcpy (info, " Board: TQM5200 (TQ-Components GmbH)");
-#if defined (CONFIG_STK52XX)
+#if defined (CONFIG_STK52XX) || defined (CONFIG_TB5200)
 	} else if (line_number == 2) {
-		strcpy (info, "        on a STK52XX baseboard");
+#if defined (CONFIG_STK52XX)
+		strcpy (info, "        on a STK52xx carrier board");
+#endif
+#if defined (CONFIG_TB5200)
+		strcpy (info, "        on a TB5200 carrier board");
+#endif
 #endif
 	}
 	else {

board/tqm834x/tqm834x.c

@@ -424,10 +424,12 @@ static void set_ddr_config(void) {
 		 * which has to be written with a certain value defined by
 		 * errata sheet.
 		 */
+		u32 *reserved_p = (u32 *)((u8 *)im + 0x2f00);
+
 #if defined(DDR_CASLAT_20)
-		*((u8 *)im + 0x2f00) = 0x201c0000;
+		*reserved_p = 0x201c0000;
 #else
-		*((u8 *)im + 0x2f00) = 0x202c0000;
+		*reserved_p = 0x202c0000;
 #endif
 	}
 }

board/tqm85xx/tqm85xx.c

@@ -27,10 +27,6 @@
  * MA 02111-1307 USA
  */
 
-#ifdef CONFIG_PS2MULT
-void ps2mult_early_init(void);
-#endif
-
 #include <common.h>
 #include <pci.h>
 #include <asm/processor.h>
@@ -47,6 +43,10 @@ void local_bus_init (void);
 long int fixed_sdram (void);
 ulong flash_get_size (ulong base, int banknum);
 
+#ifdef CONFIG_PS2MULT
+void ps2mult_early_init(void);
+#endif
+
 #ifdef CONFIG_CPM2
 /*
  * I/O Port configuration table
@@ -423,4 +423,3 @@ int board_early_init_r (void)
 	return (0);
 }
 #endif /* CONFIG_BOARD_EARLY_INIT_R */
-

board/tqm8xx/flash.c

@@ -33,12 +33,13 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M)
+#if defined(CONFIG_TQM8xxL) && !defined(CONFIG_TQM866M) \
+    && !defined(CONFIG_TQM885D)
 # ifndef CFG_OR_TIMING_FLASH_AT_50MHZ
 #  define CFG_OR_TIMING_FLASH_AT_50MHZ	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 					 OR_SCY_2_CLK | OR_EHTR | OR_BI)
 # endif
-#endif /* CONFIG_TQM8xxL/M, !TQM866M */
+#endif /* CONFIG_TQM8xxL/M, !TQM866M, !TQM885D */
 
 #ifndef	CFG_ENV_ADDR
 #define CFG_ENV_ADDR	(CFG_FLASH_BASE + CFG_ENV_OFFSET)

board/tqm8xx/tqm8xx.c

@@ -119,6 +119,10 @@ int checkboard (void)
 		gd->board_type = 'M';
 	}
 
+	if ((*(s + 6) == 'D')) {	/* a TQM885D type */
+		gd->board_type = 'D';
+	}
+
 	for (; *s; ++s) {
 		if (*s == ' ')
 			break;
@@ -178,7 +182,8 @@ long int initdram (int board_type)
 
 #ifndef	CONFIG_CAN_DRIVER
 	if ((board_type != 'L') &&
-	    (board_type != 'M') ) {	/* "L" and "M" type boards have only one bank SDRAM */
+	    (board_type != 'M') &&
+	    (board_type != 'D') ) {	/* "L" and "M" type boards have only one bank SDRAM */
 		memctl->memc_or3 = CFG_OR3_PRELIM;
 		memctl->memc_br3 = CFG_BR3_PRELIM;
 	}
@@ -197,7 +202,8 @@ long int initdram (int board_type)
 
 #ifndef	CONFIG_CAN_DRIVER
 	if ((board_type != 'L') &&
-	    (board_type != 'M') ) {	/* "L" and "M" type boards have only one bank SDRAM */
+	    (board_type != 'M') &&
+	    (board_type != 'D') ) {	/* only one SDRAM bank on L, M and D modules */
 		memctl->memc_mcr = 0x80006105;	/* SDRAM bank 1 */
 		udelay (1);
 		memctl->memc_mcr = 0x80006230;	/* SDRAM bank 1 - execute twice */
@@ -214,8 +220,7 @@ long int initdram (int board_type)
 	 *
 	 * try 8 column mode
 	 */
-	size8 = dram_size (CFG_MAMR_8COL, SDRAM_BASE2_PRELIM,
+	size8 = dram_size (CFG_MAMR_8COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
-					   SDRAM_MAX_SIZE);
 	debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size8 >> 20);
 
 	udelay (1000);
@@ -223,8 +228,7 @@ long int initdram (int board_type)
 	/*
 	 * try 9 column mode
 	 */
-	size9 = dram_size (CFG_MAMR_9COL, SDRAM_BASE2_PRELIM,
+	size9 = dram_size (CFG_MAMR_9COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
-					   SDRAM_MAX_SIZE);
 	debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size9 >> 20);
 
 	udelay(1000);
@@ -233,8 +237,7 @@ long int initdram (int board_type)
 	/*
 	 * try 10 column mode
 	 */
-	size10 = dram_size (CFG_MAMR_10COL, (ulong *) SDRAM_BASE2_PRELIM,
+	size10 = dram_size (CFG_MAMR_10COL, SDRAM_BASE2_PRELIM, SDRAM_MAX_SIZE);
-					     SDRAM_MAX_SIZE);
 	debug ("SDRAM Bank 0 in 10 column mode: %ld MB\n", size10 >> 20);
 #else
 	size10 = 0;
@@ -255,7 +258,8 @@ long int initdram (int board_type)
 
 #ifndef	CONFIG_CAN_DRIVER
 	if ((board_type != 'L') &&
-	    (board_type != 'M') ) {	/* "L" and "M" type boards have only one bank SDRAM */
+	    (board_type != 'M') &&
+	    (board_type != 'D') ) {	/* "L" and "M" type boards have only one bank SDRAM */
 		/*
 		 * Check Bank 1 Memory Size
 		 * use current column settings

board/trab/auto_update.c

@@ -57,9 +57,9 @@
  *		valid then run it.
  *	2) if preinst.img is found load it into memory. If it is
  *		valid then run it. Update the EEPROM.
- *	3) if firmware.img is found load it into memory. If it is valid,
+ *	3) if firmw_01.img is found load it into memory. If it is valid,
  *		burn it into FLASH and update the EEPROM.
- *	4) if kernel.img is found load it into memory. If it is valid,
+ *	4) if kernl_01.img is found load it into memory. If it is valid,
  *		burn it into FLASH and update the EEPROM.
  *	5) if app.img is found load it into memory. If it is valid,
  *		burn it into FLASH and update the EEPROM.
@@ -81,8 +81,8 @@
 /* possible names of files on the USB stick. */
 #define AU_PREPARE	"prepare.img"
 #define AU_PREINST	"preinst.img"
-#define AU_FIRMWARE	"firmware.img"
+#define AU_FIRMWARE	"firmw_01.img"
-#define AU_KERNEL	"kernel.img"
+#define AU_KERNEL	"kernl_01.img"
 #define AU_APP		"app.img"
 #define AU_DISK		"disk.img"
 #define AU_POSTINST	"postinst.img"

board/trab/flash.c

@@ -281,10 +281,12 @@ int flash_erase (flash_info_t * info, int s_first, int s_last)
 
 			if (chip1 == ERR || chip2 == ERR) {
 				rc = ERR_PROG_ERROR;
+				printf ("Flash erase error\n");
 				goto outahere;
 			}
 			if (chip1 == TMO) {
 				rc = ERR_TIMOUT;
+				printf ("Flash erase timeout error\n");
 				goto outahere;
 			}
 		}
@@ -340,7 +342,9 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 #endif
 	iflag = disable_interrupts ();
 
-	*addr = CMD_PROGRAM;
+	MEM_FLASH_ADDR1 = CMD_UNLOCK1;
+	MEM_FLASH_ADDR2 = CMD_UNLOCK2;
+	MEM_FLASH_ADDR1 = CMD_PROGRAM;
 	*addr = data;
 
 	/* arm simple, non interrupt dependent timer */
@@ -352,7 +356,7 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 		result = *addr;
 
 		/* check timeout */
-		if (get_timer_masked () > CFG_FLASH_ERASE_TOUT) {
+		if (get_timer_masked () > CFG_FLASH_WRITE_TOUT) {
 			chip1 = ERR | TMO;
 			break;
 		}
@@ -384,8 +388,13 @@ static int write_word (flash_info_t * info, ulong dest, ulong data)
 
 	*addr = CMD_READ_ARRAY;
 
-	if (chip1 == ERR || chip2 == ERR || *addr != data)
+	if (chip1 == ERR || chip2 == ERR || *addr != data) {
 		rc = ERR_PROG_ERROR;
+		printf ("Flash program error\n");
+		debug ("chip1: %#x, chip2: %#x, addr: %#lx *addr: %#lx, "
+		       "data: %#lx\n",
+		       chip1, chip2, addr, *addr, data);
+	}
 
 	if (iflag)
 		enable_interrupts ();
@@ -408,10 +417,6 @@ int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
 	int l;
 	int i, rc;
 
-	MEM_FLASH_ADDR1 = CMD_UNLOCK1;
-	MEM_FLASH_ADDR2 = CMD_UNLOCK2;
-	MEM_FLASH_ADDR1 = CMD_UNLOCK_BYPASS;
-
 	wp = (addr & ~3);	/* get lower word aligned address */
 
 	/*
@@ -479,9 +484,6 @@ int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
 
 	Done:
 
-	MEM_FLASH_ADDR = CMD_UNLOCK_BYPASS_RES1;
-	MEM_FLASH_ADDR = CMD_UNLOCK_BYPASS_RES2;
-
 	return (rc);
 }
 
@@ -515,7 +517,7 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 		info->flash_id = FLASH_UNKNOWN;
 		info->sector_count = 0;
 		info->size = 0;
-		addr[0] = 0x00FF00FF;		/* restore read mode */
+		addr[0] = CMD_READ_ARRAY;	/* restore read mode */
 		debug ("## flash_init: unknown manufacturer\n");
 		return (0);			/* no or unknown flash	*/
 	}
@@ -530,7 +532,7 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 		info->sector_count = 71;
 		info->size = 0x00800000;
 
-		addr[0] = 0x00FF00FF;		/* restore read mode */
+		addr[0] = CMD_READ_ARRAY;	/* restore read mode */
 		break;				/* =>  8 MB		*/
 
 	case AMD_ID_LV640U:
@@ -538,7 +540,7 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 		info->sector_count = 128;
 		info->size = 0x01000000;
 
-		addr[0] = 0x00F000F0;		/* restore read mode */
+		addr[0] = CMD_READ_ARRAY;	/* restore read mode */
 		break;				/* => 16 MB		*/
 
 	case MX_ID_LV320B:
@@ -546,13 +548,13 @@ static ulong flash_get_size (vu_long *addr, flash_info_t *info)
 		info->sector_count = 71;
 		info->size = 0x00800000;
 
-		addr[0] = 0x00FF00FF;		/* restore read mode */
+		addr[0] = CMD_READ_ARRAY;	/* restore read mode */
 		break;				/* =>  8 MB		*/
 
 	default:
 		debug ("## flash_init: unknown flash chip\n");
 		info->flash_id = FLASH_UNKNOWN;
-		addr[0] = 0x00FF00FF;		/* restore read mode */
+		addr[0] = CMD_READ_ARRAY;	/* restore read mode */
 		return (0);			/* => no or unknown flash */
 
 	}

board/trab/vfd.c

@@ -251,19 +251,17 @@ void create_vfd_table(void)
 			    unsigned long adr  = gd->fb_base;
 			    unsigned int bit_nr = 0;
 
-			    if (vfd_table[x][y][color][display][entry]) {
+			    pixel  = vfd_table[x][y][color][display][entry] + frame_buf_offs;
+			    /*
+			     * wrap arround if offset
+			     * (see manual S3C2400)
+			     */
+			    if (pixel>=FRAME_BUF_SIZE*8)
+				    pixel = pixel-(FRAME_BUF_SIZE*8);
+			    adr    = gd->fb_base+(pixel/32)*4+(3-(pixel%32)/8);
+			    bit_nr = pixel%8;
+			    bit_nr = (bit_nr>3)?bit_nr-4:bit_nr+4;
 
-				pixel  = vfd_table[x][y][color][display][entry] + frame_buf_offs;
-				 /*
-				  * wrap arround if offset
-				  * (see manual S3C2400)
-				  */
-				if (pixel>=FRAME_BUF_SIZE*8)
-					pixel = pixel-(FRAME_BUF_SIZE*8);
-				adr    = gd->fb_base+(pixel/32)*4+(3-(pixel%32)/8);
-				bit_nr = pixel%8;
-				bit_nr = (bit_nr>3)?bit_nr-4:bit_nr+4;
-			    }
 			    adr_vfd_table[x][y][color][display][entry] = adr;
 			    bit_vfd_table[x][y][color][display][entry] = bit_nr;
 			}

board/uc100/Makefile

@@ -25,8 +25,8 @@ include $(TOPDIR)/config.mk
 
 LIB	= lib$(BOARD).a
 
-#OBJS	= $(BOARD).o flash.o
+#OBJS	= $(BOARD).o flash.o pcmcia.o
-OBJS	= $(BOARD).o
+OBJS	= $(BOARD).o pcmcia.o
 
 $(LIB):	.depend $(OBJS)
 	$(AR) crv $@ $(OBJS)

board/uc100/pcmcia.c

@@ -0,0 +1,198 @@
+#include <common.h>
+#include <mpc8xx.h>
+#include <pcmcia.h>
+
+#undef	CONFIG_PCMCIA
+
+#if	(CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+#define	CONFIG_PCMCIA
+#endif
+
+#if	(CONFIG_COMMANDS & CFG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
+#define	CONFIG_PCMCIA
+#endif
+
+#ifdef	CONFIG_PCMCIA
+
+#define PCMCIA_BOARD_MSG "UC100"
+
+/*
+ * Remark: don't turn off OE "__MY_PCMCIA_GCRX_CXOE" on UC100 board.
+ *         This leads to board-hangup! (sr, 8 Dez. 2004)
+ */
+static void cfg_ports (void)
+{
+	volatile immap_t	*immap;
+
+	immap = (immap_t *)CFG_IMMR;
+
+	/*
+	* Configure Port A for MAX1602 PC-Card Power-Interface Switch
+	*/
+	immap->im_ioport.iop_padat &= ~0x8000;	/* set port x output to low */
+	immap->im_ioport.iop_padir |= 0x8000;	/* enable port x as output */
+
+	debug ("Set Port A: PAR: %08x DIR: %08x DAT: %08x\n",
+	       immap->im_ioport.iop_papar, immap->im_ioport.iop_padir,
+	       immap->im_ioport.iop_padat);
+}
+
+int pcmcia_hardware_enable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	volatile sysconf8xx_t	*sysp;
+	uint reg, mask;
+
+	debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	udelay(10000);
+
+	immap = (immap_t *)CFG_IMMR;
+	sysp  = (sysconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_siu_conf));
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	cp    = (cpm8xx_t *)(&(((immap_t *)CFG_IMMR)->im_cpm));
+
+	/* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
+	cfg_ports ();
+
+	/*
+	* Configure SIUMCR to enable PCMCIA port B
+	* (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
+	*/
+	sysp->sc_siumcr &= ~SIUMCR_DBGC11;	/* set DBGC to 00 */
+
+	/* clear interrupt state, and disable interrupts */
+	pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
+	pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
+
+	/*
+	* Disable interrupts, DMA, and PCMCIA buffers
+	* (isolate the interface) and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Make sure there is a card in the slot, then configure the interface.
+	*/
+	udelay(10000);
+	debug ("[%d] %s: PIPR(%p)=0x%x\n",
+	       __LINE__,__FUNCTION__,
+	       &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
+	if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
+		printf ("   No Card found\n");
+		return (1);
+	}
+
+	/*
+	* Power On.
+	*/
+	mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
+	reg  = pcmp->pcmc_pipr;
+	debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
+	       reg,
+	       (reg&PCMCIA_VS1(slot))?"n":"ff",
+	       (reg&PCMCIA_VS2(slot))?"n":"ff");
+	if ((reg & mask) == mask) {
+		puts (" 5.0V card found: ");
+	} else {
+		puts (" 3.3V card found: ");
+	}
+
+	/*  switch VCC on */
+	immap->im_ioport.iop_padat |= 0x8000; /* power enable 3.3V */
+
+	udelay(10000);
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(250000);	/* some cards need >150 ms to come up :-( */
+
+	debug ("# hardware_enable done\n");
+
+	return (0);
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_PCMCIA)
+int pcmcia_hardware_disable(int slot)
+{
+	volatile immap_t	*immap;
+	volatile cpm8xx_t	*cp;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+
+	/* switch VCC off */
+	immap->im_ioport.iop_padat &= ~0x8000; /* power disable 3.3V */
+
+	/* Configure PCMCIA General Control Register */
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = 0;
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+
+	udelay(10000);
+
+	return (0);
+}
+#endif	/* CFG_CMD_PCMCIA */
+
+
+int pcmcia_voltage_set(int slot, int vcc, int vpp)
+{
+	volatile immap_t	*immap;
+	volatile pcmconf8xx_t	*pcmp;
+	u_long reg;
+
+	debug ("voltage_set: "
+			PCMCIA_BOARD_MSG
+			" Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
+	'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
+
+	immap = (immap_t *)CFG_IMMR;
+	pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CFG_IMMR)->im_pcmcia));
+	/*
+	* Disable PCMCIA buffers (isolate the interface)
+	* and assert RESET signal
+	*/
+	debug ("Disable PCMCIA buffers and assert RESET\n");
+	reg  = PCMCIA_PGCRX(_slot_);
+	reg |= __MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	/*
+	* Configure Port C pins for
+	* 5 Volts Enable and 3 Volts enable,
+	* Turn all power pins to Hi-Z
+	*/
+	debug ("PCMCIA power OFF\n");
+	cfg_ports ();	/* Enables switch, but all in Hi-Z */
+
+	debug ("Enable PCMCIA buffers and stop RESET\n");
+	reg  =  PCMCIA_PGCRX(_slot_);
+	reg &= ~__MY_PCMCIA_GCRX_CXRESET;	/* active high */
+	reg &= ~__MY_PCMCIA_GCRX_CXOE;		/* active low  */
+	PCMCIA_PGCRX(_slot_) = reg;
+	udelay(500);
+
+	debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
+	       slot+'A');
+	return (0);
+}
+
+#endif	/* CONFIG_PCMCIA */

common/cmd_bdinfo.c

@@ -61,11 +61,12 @@ int do_bdinfo ( cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	print_num ("bootflags",	    bd->bi_bootflags	);
 #if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
     defined(CONFIG_405EP) || defined(CONFIG_XILINX_ML300) || \
-    defined(CONFIG_440EP) || defined(CONFIG_440GR)
+    defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
+	defined(CONFIG_440SP)
 	print_str ("procfreq",	    strmhz(buf, bd->bi_procfreq));
 	print_str ("plb_busfreq",   strmhz(buf, bd->bi_plb_busfreq));
 #if defined(CONFIG_405GP) || defined(CONFIG_405EP) || defined(CONFIG_XILINX_ML300) || \
-    defined(CONFIG_440EP) || defined(CONFIG_440GR)
+    defined(CONFIG_440EP) || defined(CONFIG_440GR) || defined(CONFIG_440SPE)
 	print_str ("pci_busfreq",   strmhz(buf, bd->bi_pci_busfreq));
 #endif
 #else	/* ! CONFIG_405GP, CONFIG_405CR, CONFIG_405EP, CONFIG_XILINX_ML300, CONFIG_440EP CONFIG_440GR */

common/cmd_mem.c

@@ -707,7 +707,7 @@ int do_mem_mtest (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 #if defined(CFG_MEMTEST_SCRATCH)
 	vu_long *dummy = (vu_long*)CFG_MEMTEST_SCRATCH;
 #else
-	vu_long *dummy = NULL;
+	vu_long *dummy = 0;	/* yes, this is address 0x0, not NULL */
 #endif
 	int	j;
 	int iterations = 1;

common/cmd_mii.c

@@ -57,6 +57,11 @@ int do_mii (cmd_tbl_t * cmdtp, int flag, int argc, char *argv[])
 	int		rcode = 0;
 	char		*devname;
 
+	if (argc < 2) {
+		printf ("Usage:\n%s\n", cmdtp->usage);
+		return 1;
+	}
+
 #if defined(CONFIG_8xx) || defined(CONFIG_MCF52x2)
 	mii_init ();
 #endif

common/cmd_reginfo.c

@@ -328,7 +328,7 @@ int do_reginfo (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		(*(volatile ulong*)MPC5XXX_ADDECR & 0x02000000) ? 1 : 0);
 	printf ("\tSDRAMCS0: %08X\n",
 		*(volatile ulong*)MPC5XXX_SDRAM_CS0CFG);
-	printf ("\tSDRAMCS0: %08X\n",
+	printf ("\tSDRAMCS1: %08X\n",
 		*(volatile ulong*)MPC5XXX_SDRAM_CS1CFG);
 #endif /* CONFIG_MPC5200 */
 	return 0;

common/cmd_usb.c

@@ -186,7 +186,7 @@ void usb_display_conf_desc(struct usb_config_descriptor *config,struct usb_devic
 void usb_display_if_desc(struct usb_interface_descriptor *ifdesc,struct usb_device *dev)
 {
 	printf("     Interface: %d\n",ifdesc->bInterfaceNumber);
-	printf("     - Alternate Settings %d, Endpoints: %d\n",ifdesc->bAlternateSetting,ifdesc->bNumEndpoints);
+	printf("     - Alternate Setting %d, Endpoints: %d\n",ifdesc->bAlternateSetting,ifdesc->bNumEndpoints);
 	printf("     - Class ");
 	usb_display_class_sub(ifdesc->bInterfaceClass,ifdesc->bInterfaceSubClass,ifdesc->bInterfaceProtocol);
 	printf("\n");
@@ -444,6 +444,7 @@ int do_usb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 
 	int i;
 	struct usb_device *dev = NULL;
+	extern char usb_started;
 #ifdef CONFIG_USB_STORAGE
 	block_dev_desc_t *stor_dev;
 #endif
@@ -477,6 +478,10 @@ int do_usb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 		usb_stop();
 		return 0;
 	}
+	if (!usb_started) {
+		printf("USB is stopped. Please issue 'usb start' first.\n");
+		return 1;
+	}
 	if (strncmp(argv[1],"tree",4) == 0) {
 		printf("\nDevice Tree:\n");
 		usb_show_tree(usb_get_dev_index(0));

common/crc16.c

@@ -101,7 +101,7 @@ cyg_crc16(unsigned char *buf, int len)
 
     cksum = 0;
     for (i = 0;  i < len;  i++) {
-        cksum = crc16_tab[((cksum>>8) ^ *buf++) & 0xFF] ^ (cksum << 8);
+	cksum = crc16_tab[((cksum>>8) ^ *buf++) & 0xFF] ^ (cksum << 8);
     }
     return cksum;
 }

common/main.c

@@ -2,6 +2,10 @@
  * (C) Copyright 2000
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
+ * Add to readline cmdline-editing by
+ * (C) Copyright 2005
+ * JinHua Luo, GuangDong Linux Center, <luo.jinhua@gd-linux.com>
+ *
  * See file CREDITS for list of people who contributed to this
  * project.
  *
@@ -49,7 +53,6 @@ extern int do_bootd (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]);
 
 #define MAX_DELAY_STOP_STR 32
 
-static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen);
 static int parse_line (char *, char *[]);
 #if defined(CONFIG_BOOTDELAY) && (CONFIG_BOOTDELAY >= 0)
 static int abortboot(int);
@@ -59,8 +62,11 @@ static int abortboot(int);
 
 char        console_buffer[CFG_CBSIZE];		/* console I/O buffer	*/
 
+#ifndef CONFIG_CMDLINE_EDITING
+static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen);
 static char erase_seq[] = "\b \b";		/* erase sequence	*/
 static char   tab_seq[] = "        ";		/* used to expand TABs	*/
+#endif /* CONFIG_CMDLINE_EDITING */
 
 #ifdef CONFIG_BOOT_RETRY_TIME
 static uint64_t endtime = 0;  /* must be set, default is instant timeout */
@@ -516,6 +522,406 @@ void reset_cmd_timeout(void)
 }
 #endif
 
+#ifdef CONFIG_CMDLINE_EDITING
+
+/*
+ * cmdline-editing related codes from vivi.
+ * Author: Janghoon Lyu <nandy@mizi.com>
+ */
+
+#if 1	/* avoid redundand code -- wd */
+#define putnstr(str,n)	do {			\
+		printf ("%.*s", n, str);	\
+	} while (0)
+#else
+void putnstr(const char *str, size_t n)
+{
+	if (str == NULL)
+		return;
+
+	while (n && *str != '\0') {
+		putc(*str);
+		str++;
+		n--;
+	}
+}
+#endif
+
+#define CTL_CH(c)		((c) - 'a' + 1)
+
+#define MAX_CMDBUF_SIZE		256
+
+#define CTL_BACKSPACE		('\b')
+#define DEL			((char)255)
+#define DEL7			((char)127)
+#define CREAD_HIST_CHAR		('!')
+
+#define getcmd_putch(ch)	putc(ch)
+#define getcmd_getch()		getc()
+#define getcmd_cbeep()		getcmd_putch('\a')
+
+#define HIST_MAX		20
+#define HIST_SIZE		MAX_CMDBUF_SIZE
+
+static int hist_max = 0;
+static int hist_add_idx = 0;
+static int hist_cur = -1;
+unsigned hist_num = 0;
+
+char* hist_list[HIST_MAX];
+char hist_lines[HIST_MAX][HIST_SIZE];
+
+#define add_idx_minus_one() ((hist_add_idx == 0) ? hist_max : hist_add_idx-1)
+
+static void hist_init(void)
+{
+	int i;
+
+	hist_max = 0;
+	hist_add_idx = 0;
+	hist_cur = -1;
+	hist_num = 0;
+
+	for (i = 0; i < HIST_MAX; i++) {
+		hist_list[i] = hist_lines[i];
+		hist_list[i][0] = '\0';
+	}
+}
+
+static void cread_add_to_hist(char *line)
+{
+	strcpy(hist_list[hist_add_idx], line);
+
+	if (++hist_add_idx >= HIST_MAX)
+		hist_add_idx = 0;
+
+	if (hist_add_idx > hist_max)
+		hist_max = hist_add_idx;
+
+	hist_num++;
+}
+
+static char* hist_prev(void)
+{
+	char *ret;
+	int old_cur;
+
+	if (hist_cur < 0)
+		return NULL;
+
+	old_cur = hist_cur;
+	if (--hist_cur < 0)
+		hist_cur = hist_max;
+
+	if (hist_cur == hist_add_idx) {
+		hist_cur = old_cur;
+		ret = NULL;
+	} else
+		ret = hist_list[hist_cur];
+
+	return (ret);
+}
+
+static char* hist_next(void)
+{
+	char *ret;
+
+	if (hist_cur < 0)
+		return NULL;
+
+	if (hist_cur == hist_add_idx)
+		return NULL;
+
+	if (++hist_cur > hist_max)
+		hist_cur = 0;
+
+	if (hist_cur == hist_add_idx) {
+		ret = "";
+	} else
+		ret = hist_list[hist_cur];
+
+	return (ret);
+}
+
+#ifndef CONFIG_CMDLINE_EDITING
+static void cread_print_hist_list(void)
+{
+	int i;
+	unsigned long n;
+
+	n = hist_num - hist_max;
+
+	i = hist_add_idx + 1;
+	while (1) {
+		if (i > hist_max)
+			i = 0;
+		if (i == hist_add_idx)
+			break;
+		printf("%s\n", hist_list[i]);
+		n++;
+		i++;
+	}
+}
+#endif /* CONFIG_CMDLINE_EDITING */
+
+#define BEGINNING_OF_LINE() {			\
+	while (num) {				\
+		getcmd_putch(CTL_BACKSPACE);	\
+		num--;				\
+	}					\
+}
+
+#define ERASE_TO_EOL() {				\
+	if (num < eol_num) {				\
+		int tmp;				\
+		for (tmp = num; tmp < eol_num; tmp++)	\
+			getcmd_putch(' ');		\
+		while (tmp-- > num)			\
+			getcmd_putch(CTL_BACKSPACE);	\
+		eol_num = num;				\
+	}						\
+}
+
+#define REFRESH_TO_EOL() {			\
+	if (num < eol_num) {			\
+		wlen = eol_num - num;		\
+		putnstr(buf + num, wlen);	\
+		num = eol_num;			\
+	}					\
+}
+
+static void cread_add_char(char ichar, int insert, unsigned long *num,
+	       unsigned long *eol_num, char *buf, unsigned long len)
+{
+	unsigned long wlen;
+
+	/* room ??? */
+	if (insert || *num == *eol_num) {
+		if (*eol_num > len - 1) {
+			getcmd_cbeep();
+			return;
+		}
+		(*eol_num)++;
+	}
+
+	if (insert) {
+		wlen = *eol_num - *num;
+		if (wlen > 1) {
+			memmove(&buf[*num+1], &buf[*num], wlen-1);
+		}
+
+		buf[*num] = ichar;
+		putnstr(buf + *num, wlen);
+		(*num)++;
+		while (--wlen) {
+			getcmd_putch(CTL_BACKSPACE);
+		}
+	} else {
+		/* echo the character */
+		wlen = 1;
+		buf[*num] = ichar;
+		putnstr(buf + *num, wlen);
+		(*num)++;
+	}
+}
+
+static void cread_add_str(char *str, int strsize, int insert, unsigned long *num,
+	      unsigned long *eol_num, char *buf, unsigned long len)
+{
+	while (strsize--) {
+		cread_add_char(*str, insert, num, eol_num, buf, len);
+		str++;
+	}
+}
+
+static int cread_line(char *buf, unsigned int *len)
+{
+	unsigned long num = 0;
+	unsigned long eol_num = 0;
+	unsigned long rlen;
+	unsigned long wlen;
+	char ichar;
+	int insert = 1;
+	int esc_len = 0;
+	int rc = 0;
+	char esc_save[8];
+
+	while (1) {
+		rlen = 1;
+		ichar = getcmd_getch();
+
+		if ((ichar == '\n') || (ichar == '\r')) {
+			putc('\n');
+			break;
+		}
+
+		/*
+		 * handle standard linux xterm esc sequences for arrow key, etc.
+		 */
+		if (esc_len != 0) {
+			if (esc_len == 1) {
+				if (ichar == '[') {
+					esc_save[esc_len] = ichar;
+					esc_len = 2;
+				} else {
+					cread_add_str(esc_save, esc_len, insert,
+						      &num, &eol_num, buf, *len);
+					esc_len = 0;
+				}
+				continue;
+			}
+
+			switch (ichar) {
+
+			case 'D':	/* <- key */
+				ichar = CTL_CH('b');
+				esc_len = 0;
+				break;
+			case 'C':	/* -> key */
+				ichar = CTL_CH('f');
+				esc_len = 0;
+				break;	/* pass off to ^F handler */
+			case 'H':	/* Home key */
+				ichar = CTL_CH('a');
+				esc_len = 0;
+				break;	/* pass off to ^A handler */
+			case 'A':	/* up arrow */
+				ichar = CTL_CH('p');
+				esc_len = 0;
+				break;	/* pass off to ^P handler */
+			case 'B':	/* down arrow */
+				ichar = CTL_CH('n');
+				esc_len = 0;
+				break;	/* pass off to ^N handler */
+			default:
+				esc_save[esc_len++] = ichar;
+				cread_add_str(esc_save, esc_len, insert,
+					      &num, &eol_num, buf, *len);
+				esc_len = 0;
+				continue;
+			}
+		}
+
+		switch (ichar) {
+		case 0x1b:
+			if (esc_len == 0) {
+				esc_save[esc_len] = ichar;
+				esc_len = 1;
+			} else {
+				puts("impossible condition #876\n");
+				esc_len = 0;
+			}
+			break;
+
+		case CTL_CH('a'):
+			BEGINNING_OF_LINE();
+			break;
+		case CTL_CH('c'):	/* ^C - break */
+			*buf = '\0';	/* discard input */
+			return (-1);
+		case CTL_CH('f'):
+			if (num < eol_num) {
+				getcmd_putch(buf[num]);
+				num++;
+			}
+			break;
+		case CTL_CH('b'):
+			if (num) {
+				getcmd_putch(CTL_BACKSPACE);
+				num--;
+			}
+			break;
+		case CTL_CH('d'):
+			if (num < eol_num) {
+				wlen = eol_num - num - 1;
+				if (wlen) {
+					memmove(&buf[num], &buf[num+1], wlen);
+					putnstr(buf + num, wlen);
+				}
+
+				getcmd_putch(' ');
+				do {
+					getcmd_putch(CTL_BACKSPACE);
+				} while (wlen--);
+				eol_num--;
+			}
+			break;
+		case CTL_CH('k'):
+			ERASE_TO_EOL();
+			break;
+		case CTL_CH('e'):
+			REFRESH_TO_EOL();
+			break;
+		case CTL_CH('o'):
+			insert = !insert;
+			break;
+		case CTL_CH('x'):
+			BEGINNING_OF_LINE();
+			ERASE_TO_EOL();
+			break;
+		case DEL:
+		case DEL7:
+		case 8:
+			if (num) {
+				wlen = eol_num - num;
+				num--;
+				memmove(&buf[num], &buf[num+1], wlen);
+				getcmd_putch(CTL_BACKSPACE);
+				putnstr(buf + num, wlen);
+				getcmd_putch(' ');
+				do {
+					getcmd_putch(CTL_BACKSPACE);
+				} while (wlen--);
+				eol_num--;
+			}
+			break;
+		case CTL_CH('p'):
+		case CTL_CH('n'):
+		{
+			char * hline;
+
+			esc_len = 0;
+
+			if (ichar == CTL_CH('p'))
+				hline = hist_prev();
+			else
+				hline = hist_next();
+
+			if (!hline) {
+				getcmd_cbeep();
+				continue;
+			}
+
+			/* nuke the current line */
+			/* first, go home */
+			BEGINNING_OF_LINE();
+
+			/* erase to end of line */
+			ERASE_TO_EOL();
+
+			/* copy new line into place and display */
+			strcpy(buf, hline);
+			eol_num = strlen(buf);
+			REFRESH_TO_EOL();
+			continue;
+		}
+		default:
+			cread_add_char(ichar, insert, &num, &eol_num, buf, *len);
+			break;
+		}
+	}
+	*len = eol_num;
+	buf[eol_num] = '\0';	/* lose the newline */
+
+	if (buf[0] && buf[0] != CREAD_HIST_CHAR)
+		cread_add_to_hist(buf);
+	hist_cur = hist_add_idx;
+
+	return (rc);
+}
+
+#endif /* CONFIG_CMDLINE_EDITING */
+
 /****************************************************************************/
 
 /*
@@ -528,6 +934,21 @@ void reset_cmd_timeout(void)
  */
 int readline (const char *const prompt)
 {
+#ifdef CONFIG_CMDLINE_EDITING
+	char *p = console_buffer;
+	unsigned int len=MAX_CMDBUF_SIZE;
+	static int initted = 0;
+
+	if (!initted) {
+		hist_init();
+		initted = 1;
+	}
+
+	puts (prompt);
+
+	cread_line(p, &len);
+	return len;
+#else
 	char   *p = console_buffer;
 	int	n = 0;				/* buffer index		*/
 	int	plen = 0;			/* prompt length	*/
@@ -623,10 +1044,12 @@ int readline (const char *const prompt)
 			}
 		}
 	}
+#endif /* CONFIG_CMDLINE_EDITING */
 }
 
 /****************************************************************************/
 
+#ifndef CONFIG_CMDLINE_EDITING
 static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen)
 {
 	char *s;
@@ -656,6 +1079,7 @@ static char * delete_char (char *buffer, char *p, int *colp, int *np, int plen)
 	(*np)--;
 	return (p);
 }
+#endif /* CONFIG_CMDLINE_EDITING */
 
 /****************************************************************************/
 

common/serial.c

@@ -42,7 +42,11 @@ struct serial_device *default_serial_console (void)
 	return &serial_scc_device;
 #elif defined(CONFIG_405GP) || defined(CONFIG_405CR) || defined(CONFIG_440) \
    || defined(CONFIG_405EP) || defined(CONFIG_MPC5xxx)
-	return &serial0_device;
+#if defined(CONFIG_UART1_CONSOLE)
+		return &serial1_device;
+#else
+		return &serial0_device;
+#endif
 #else
 #error No default console
 #endif

common/usb.c

@@ -72,6 +72,8 @@ static int running;
 static int asynch_allowed;
 static struct devrequest setup_packet;
 
+char usb_started; /* flag for the started/stopped USB status */
+
 /**********************************************************************
  * some forward declerations...
  */
@@ -110,10 +112,12 @@ int usb_init(void)
 		printf("scanning bus for devices... ");
 		running=1;
 		usb_scan_devices();
+		usb_started = 1;
 		return 0;
 	}
 	else {
 		printf("Error, couldn't init Lowlevel part\n");
+		usb_started = 0;
 		return -1;
 	}
 }
@@ -124,6 +128,7 @@ int usb_init(void)
 int usb_stop(void)
 {
 	asynch_allowed=1;
+	usb_started = 0;
 	usb_hub_reset();
 	return usb_lowlevel_stop();
 }
@@ -280,56 +285,68 @@ int usb_set_maxpacket(struct usb_device *dev)
 int usb_parse_config(struct usb_device *dev, unsigned char *buffer, int cfgno)
 {
 	struct usb_descriptor_header *head;
-	int index,ifno,epno;
+	int index, ifno, epno, curr_if_num;
-	ifno=-1;
+	int i;
-	epno=-1;
+	unsigned char *ch;
 
-	dev->configno=cfgno;
+	ifno = -1;
-	head =(struct usb_descriptor_header *)&buffer[0];
+	epno = -1;
-	if(head->bDescriptorType!=USB_DT_CONFIG) {
+	curr_if_num = -1;
-		printf(" ERROR: NOT USB_CONFIG_DESC %x\n",head->bDescriptorType);
+
+	dev->configno = cfgno;
+	head = (struct usb_descriptor_header *) &buffer[0];
+	if(head->bDescriptorType != USB_DT_CONFIG) {
+		printf(" ERROR: NOT USB_CONFIG_DESC %x\n", head->bDescriptorType);
 		return -1;
 	}
-	memcpy(&dev->config,buffer,buffer[0]);
+	memcpy(&dev->config, buffer, buffer[0]);
-	dev->config.wTotalLength=swap_16(dev->config.wTotalLength);
+	dev->config.wTotalLength = swap_16(dev->config.wTotalLength);
-	dev->config.no_of_if=0;
+	dev->config.no_of_if = 0;
 
-	index=dev->config.bLength;
+	index = dev->config.bLength;
 	/* Ok the first entry must be a configuration entry, now process the others */
-	head=(struct usb_descriptor_header *)&buffer[index];
+	head = (struct usb_descriptor_header *) &buffer[index];
-	while(index+1 < dev->config.wTotalLength) {
+	while(index + 1 < dev->config.wTotalLength) {
 		switch(head->bDescriptorType) {
 			case USB_DT_INTERFACE:
-				ifno=dev->config.no_of_if;
+				if(((struct usb_interface_descriptor *) &buffer[index])->
-				dev->config.no_of_if++; /* found an interface desc, increase numbers */
+					bInterfaceNumber != curr_if_num) {
-				memcpy(&dev->config.if_desc[ifno],&buffer[index],buffer[index]); /* copy new desc */
+					/* this is a new interface, copy new desc */
-				dev->config.if_desc[ifno].no_of_ep=0;
+					ifno = dev->config.no_of_if;
-
+					dev->config.no_of_if++;
+					memcpy(&dev->config.if_desc[ifno],
+						&buffer[index], buffer[index]);
+					dev->config.if_desc[ifno].no_of_ep = 0;
+					dev->config.if_desc[ifno].num_altsetting = 1;
+					curr_if_num = dev->config.if_desc[ifno].bInterfaceNumber;
+				} else {
+					/* found alternate setting for the interface */
+					dev->config.if_desc[ifno].num_altsetting++;
+				}
 				break;
 			case USB_DT_ENDPOINT:
-				epno=dev->config.if_desc[ifno].no_of_ep;
+				epno = dev->config.if_desc[ifno].no_of_ep;
 				dev->config.if_desc[ifno].no_of_ep++; /* found an endpoint */
-				memcpy(&dev->config.if_desc[ifno].ep_desc[epno],&buffer[index],buffer[index]);
+				memcpy(&dev->config.if_desc[ifno].ep_desc[epno],
-				dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize
+					&buffer[index], buffer[index]);
-					=swap_16(dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize);
+				dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize =
-				USB_PRINTF("if %d, ep %d\n",ifno,epno);
+					swap_16(dev->config.if_desc[ifno].ep_desc[epno].wMaxPacketSize);
+				USB_PRINTF("if %d, ep %d\n", ifno, epno);
 				break;
 			default:
-				if(head->bLength==0)
+				if(head->bLength == 0)
 					return 1;
-				USB_PRINTF("unknown Description Type : %x\n",head->bDescriptorType);
+				USB_PRINTF("unknown Description Type : %x\n", head->bDescriptorType);
 				{
-					int i;
+					ch = (unsigned char *)head;
-					unsigned char *ch;
+					for(i = 0; i < head->bLength; i++)
-					ch=(unsigned char *)head;
+						USB_PRINTF("%02X ", *ch++);
-					for(i=0;i<head->bLength; i++)
-						USB_PRINTF("%02X ",*ch++);
 					USB_PRINTF("\n\n\n");
 				}
 				break;
 		}
-		index+=head->bLength;
+		index += head->bLength;
-		head=(struct usb_descriptor_header *)&buffer[index];
+		head = (struct usb_descriptor_header *)&buffer[index];
 	}
 	return 1;
 }
@@ -443,6 +460,14 @@ int usb_set_interface(struct usb_device *dev, int interface, int alternate)
 		printf("selecting invalid interface %d", interface);
 		return -1;
 	}
+	/*
+	 * We should return now for devices with only one alternate setting.
+	 * According to 9.4.10 of the Universal Serial Bus Specification Revision 2.0
+	 * such devices can return with a STALL. This results in some USB sticks
+	 * timeouting during initialization and then being unusable in U-Boot.
+	 */
+	if (if_face->num_altsetting == 1)
+		return 0;
 
 	if ((ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
 	    USB_REQ_SET_INTERFACE, USB_RECIP_INTERFACE, alternate,

common/usb_storage.c

@@ -1139,6 +1139,10 @@ int usb_stor_get_info(struct usb_device *dev,struct us_data *ss,block_dev_desc_t
 	    /* USB007 Mini-USB2 Flash Drive */
 	    (dev->descriptor.idVendor == 0x066f &&
 	     dev->descriptor.idProduct == 0x2010)
+	    ||
+	    /* SanDisk Corporation Cruzer Micro 20044318410546613953 */
+	    (dev->descriptor.idVendor == 0x0781 &&
+	     dev->descriptor.idProduct == 0x5151)
 	    )
 		USB_STOR_PRINTF("usb_stor_get_info: skipping RESET..\n");
 	else

common/xyzModem.c

@@ -261,8 +261,8 @@ zm_dprintf(char *fmt, ...)
 static void
 zm_flush(void)
 {
-    char *p = zm_out_start;
 #ifdef REDBOOT
+    char *p = zm_out_start;
     while (*p) mon_write_char(*p++);
 #endif
     zm_out = zm_out_start;

cpu/arm920t/s3c24x0/interrupts.c

@@ -176,7 +176,9 @@ ulong get_tbclk (void)
 
 #if defined(CONFIG_SMDK2400) || defined(CONFIG_TRAB)
 	tbclk = timer_load_val * 100;
-#elif defined(CONFIG_SMDK2410) || defined(CONFIG_VCMA9)
+#elif defined(CONFIG_SBC2410X) || \
+      defined(CONFIG_SMDK2410) || \
+      defined(CONFIG_VCMA9)
 	tbclk = CFG_HZ;
 #else
 #	error "tbclk not configured"

cpu/mips/config.mk

@@ -21,7 +21,7 @@
 # MA 02111-1307 USA
 #
 v=$(shell \
-mips-linux-as --version|grep "GNU assembler"|awk '{print $$3}'|awk -F . '{print $$2}')
+$(CROSS_COMPILE)as --version|grep "GNU assembler"|awk '{print $$3}'|awk -F . '{print $$2}')
 MIPSFLAGS=$(shell \
 if [ "$v" -lt "14" ]; then \
 	echo "-mcpu=4kc"; \